Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.07–2016.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRC)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

for LHD


E340821E06
3.167,1.344 3.75,0.417 3.75,0.417 3.917,0.417 false 0.104,0.073 1.021,0.271 0.917,0.198 10 false V Bus: 2.156,0.563 2.771,0.76 0.615,0.198 10 false DLC3 0.781,2.229 1.552,2.427 0.771,0.198 10 false 120 Ω 6.229,2.229 7,2.427 0.771,0.198 10 false 120 Ω 0.302,2.865 3.365,3.063 3.063,0.198 10 false F81*1, F82*2, F130*3 0.302,3.031 0.76,3.229 0.458,0.198 10 false ECM 3.99,0.333 4.448,0.531 0.458,0.198 10 false F62 3.99,0.5 6.26,0.708 2.271,0.208 10 false No. 1 CAN Junction Connector 5.865,2.865 6.323,3.063 0.458,0.198 10 false F38 5.865,3.031 7.094,3.604 1.229,0.573 10 false Combination Meter Assembly 4.063,3.417 4.521,3.615 0.458,0.198 10 false 25 4.625,3.417 5.083,3.615 0.458,0.198 10 false 14 4.354,3.635 4.969,3.833 0.615,0.198 10 false CANL 3.781,3.635 4.396,3.833 0.615,0.198 10 false CANH 3.531,3.917 4.146,4.115 0.615,0.198 10 false IG1 4.448,3.917 5.063,4.115 0.615,0.198 10 false GND1 4.958,3.802 5.417,4 0.458,0.198 10 false 1 3.219,3.802 3.677,4 0.458,0.198 10 false 34 3.448,4.417 5.5,4.625 2.052,0.208 10 false A49*6, A48*7, A47*8, A35*9 3.448,4.583 6.969,4.781 3.521,0.198 10 false Brake Actuator Assembly 2.542,4.063 3.917,4.26 1.375,0.198 10 false IG1 NO. 2 0.448,3.896 2.281,4.677 1.833,0.781 10 false from Ignition or Starter Switch Assembly*4 or No. 1 Ignition Relay*5 2.5,5.167 4.333,5.365 1.833,0.198 10 false Trouble Area 4.677,6.052 6.781,6.271 2.104,0.219 10 false : CAN Main Bus Line (CANH) 4.677,6.479 6.781,6.698 2.104,0.219 10 false : CAN Main Bus Line (CANL) 4.677,6.906 6.781,7.125 2.104,0.219 10 false : CAN Branch Line (CANH) 4.677,7.313 6.781,7.531 2.104,0.219 10 false : CAN Branch Line (CANL) 0.167,5.573 3.333,5.917 3.167,0.344 10 false *1: for 2NZ-FE with Manual Transaxle 0.167,5.917 3.417,6.25 3.25,0.333 10 false *2: for Automatic Transaxle 0.167,6.25 3.458,6.76 3.292,0.51 10 false *3: for 1NR-FE or 2NR-FE 0.167,6.583 3.458,7.094 3.292,0.51 10 false *4: w/o Smart Entry and Start System 0.167,6.917 3.458,7.427 3.292,0.51 10 false *5: w/ Smart Entry and Start System 0.167,7.25 3.458,7.76 3.292,0.51 10 false *6: w/ VSC with CVT 0.167,7.583 3.458,8.094 3.292,0.51 10 false *7: w/ VSC except CVT 0.167,7.917 3.458,8.427 3.292,0.51 10 false *8: w/o VSC with CVT 0.167,8.25 3.458,8.76 3.292,0.51 10 false *9: w/o VSC except CVT


for RHD


E340822E03
2.635,1.302 3.552,0.219 3.552,0.219 3.719,0.219 false 4.167,1.302 4.656,0.719 4.656,0.719 4.823,0.719 false 0.094,0.073 1.01,0.271 0.917,0.198 10 false V Bus: 2.198,0.542 2.813,0.74 0.615,0.198 10 false DLC3 3.792,0.146 4.406,0.344 0.615,0.198 10 false F62 3.792,0.313 6.083,0.563 2.292,0.25 10 false No. 1 CAN Junction Connector 4.896,0.646 7,0.948 2.104,0.302 10 false No. 2 CAN Junction Connector 0.781,2.208 1.552,2.406 0.771,0.198 10 false 120 Ω 6.24,2.208 7.01,2.406 0.771,0.198 10 false 120 Ω 0.771,2.823 1.417,3.031 0.646,0.208 10 false F130 0.76,2.99 1.219,3.188 0.458,0.198 10 false ECM 3.865,2.813 4.323,3.01 0.458,0.198 10 false A34 3.177,1.448 3.635,1.646 0.458,0.198 10 false F71 3.177,2.094 3.635,2.292 0.458,0.198 10 false F71 4.438,2.813 4.896,3.01 0.458,0.198 10 false A34 3.26,1.26 3.719,1.458 0.458,0.198 10 false 2 3.208,1.906 3.667,2.104 0.458,0.198 10 false 13 3.677,2.813 4.135,3.01 0.458,0.198 10 false 11 4.208,2.813 4.667,3.01 0.458,0.198 10 false 22 4.323,3.375 4.781,3.573 0.458,0.198 10 false 14 3.76,3.375 4.219,3.573 0.458,0.198 10 false 25 3.792,3.594 5.167,3.792 1.375,0.198 10 false CANH 4.365,3.594 5.74,3.792 1.375,0.198 10 false CANL 3.531,3.885 4.906,4.083 1.375,0.198 10 false IG1 4.448,3.875 5.823,4.073 1.375,0.198 10 false GND1 4.958,3.76 5.417,3.958 0.458,0.198 10 false 1 3.229,3.771 3.688,3.969 0.458,0.198 10 false 34 3.385,4.385 3.844,4.583 0.458,0.198 10 false A35 3.375,4.552 6.896,4.75 3.521,0.198 10 false Brake Actuator Assembly 2.552,4.031 3.927,4.229 1.375,0.198 10 false IG1 NO. 2 0.479,3.865 2.323,4.51 1.844,0.646 10 false from Ignition or Starter Switch Assembly*1 or No. 1 Ignition Relay*2 5.833,2.823 6.292,3.021 0.458,0.198 10 false F38 5.833,2.99 7.031,3.573 1.198,0.583 10 false Combination Meter Assembly 5.958,3.948 7.156,4.531 1.198,0.583 10 false Trouble Area 0.333,6.083 2.927,6.365 2.594,0.281 10 false *1: w/o Smart Entry and Start System 0.333,6.469 2.927,6.75 2.594,0.281 10 false *2: w/ Smart Entry and Start System 1.219,6.854 5.198,7.052 3.979,0.198 10 false : CAN Main Bus Line (CANH) 4.365,6.854 6.479,7.073 2.115,0.219 10 false : CAN Branch Line (CANH) 4.365,7.25 6.479,7.469 2.115,0.219 10 false : CAN Branch Line (CANL) 1.219,7.25 5.198,7.448 3.979,0.198 10 false : CAN Main Bus Line (CANL)


CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait 60 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

2.CHECK DTC (BRAKE CONTROL SYSTEM)

B

4.CHECK DTC (BRAKE CONTROL SYSTEM)
2.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
OK
NG



OK

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

NG

GO TO DIAGNOSIS PROCEDURES INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E340846C01
1.469,0.25 1.969,0.5 0.5,0.25 1.458,2.417 1.958,2.667 0.5,0.25 0.927,1.958 1.375,1.365 true 1.51,1.927 1.375,1.448 true 0.938,4.104 1.375,3.521 true 1.531,4.094 1.385,3.604 true 0.208,0.302 0.583,0.542 0.375,0.24 12 false *A 1.594,0.302 1.927,0.521 0.333,0.219 10 false A49 1.583,2.458 1.917,2.677 0.333,0.219 10 false A48 0.75,2 1.365,2.198 0.615,0.198 10 false CANL 1.354,2 1.969,2.198 0.615,0.198 10 false CANH 0.052,0.042 0.427,0.281 0.375,0.24 10 false *a 0.229,2.344 0.604,2.583 0.375,0.24 12 false *B 0.75,4.177 1.365,4.375 0.615,0.198 10 false CANL 1.375,4.167 1.99,4.365 0.615,0.198 10 false CANH
*A for CVT
*B except CVT
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Disconnect the brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for CVT
Tester Connection Condition Specified Condition
A49-25 (CANH) - A49-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

except CVT
Tester Connection Condition Specified Condition
A48-25 (CANH) - A48-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

4.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
OK
NG



OK

5.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

NG

5.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E340847C01
1.417,0.271 1.917,0.521 0.5,0.25 1.417,2.417 1.917,2.667 0.5,0.25 0.698,2.031 1.365,1.365 true 0.688,4.198 1.375,3.521 true 1.719,4.177 1.365,3.604 true 1.719,2.01 1.365,1.438 true 0.385,0.292 0.76,0.531 0.375,0.24 12 false *A 0.406,2.469 0.781,2.708 0.375,0.24 12 false *B 0.094,0.104 0.469,0.344 0.375,0.24 10 false *a 0.531,2.083 1.146,2.281 0.615,0.198 10 false CANL 1.531,2.073 2.146,2.271 0.615,0.198 10 false CANH 0.521,4.24 1.135,4.438 0.615,0.198 10 false CANL 1.542,4.208 2.156,4.406 0.615,0.198 10 false CANH 1.542,0.313 2,0.51 0.458,0.198 10 false A47 1.552,2.469 2.01,2.667 0.458,0.198 10 false A35
*A for LHD and CVT
*B except LHD and CVT
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Disconnect the brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and CVT
Tester Connection Condition Specified Condition
A47-25 (CANH) - A47-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Standard Resistance:
except LHD and CVT
Tester Connection Condition Specified Condition
A35-25 (CANH) - A35-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)