Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2016.10–2017.10
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1544  Engine Revolution Signal Malfunction  C1545  Engine Revolution Signal Malfunction  C1573  Engine Revolution Signal Malfunction (Test Mode DTC)  


DESCRIPTION

The ECM sends engine speed signals to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1544 Engine Revolution Signal Malfunction An engine speed signal error.
·

Engine speed signal circuit

·

ECM

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light comes on.
C1545 Engine Revolution Signal Malfunction An engine speed signal error.
·

Engine speed signal circuit

·

ECM

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light does not illuminate (normal reset).
C1573 Engine Revolution Signal Malfunction (Test Mode DTC) An engine speed signal error (Test Mode DTC).
·

Engine speed signal circuit

·

ECM

·

Power steering ECU assembly


- Power Steering Warning Light does not illuminate (normal reset).

WIRING DIAGRAM

C349090E03
0.917,1.063 1.333,1.26 0.417,0.198 10 false TACH 1.375,0.948 1.625,1.115 0.25,0.167 10 false 11 0.5,1.75 0.917,1.917 0.417,0.167 10 false F130 0.5,1.917 0.917,2.083 0.417,0.167 10 false ECM 4.958,0.865 5.208,1.031 0.25,0.167 10 false 5 4.885,1.063 5.135,1.229 0.25,0.167 10 false F12 4.875,2.146 5.125,2.313 0.25,0.167 10 false F11 4.938,1.938 5.188,2.104 0.25,0.167 10 false 2 5.25,1.042 5.667,1.24 0.417,0.198 10 false TACH 5.24,2.135 5.656,2.333 0.417,0.198 10 false PGND 5.25,2.667 6.583,3.167 1.333,0.5 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.PERFORM SIGNAL CHECK (ENGINE SPEED SIGNAL)
a.

Perform the signal check in the Test Mode procedure.

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 13 3
OK:

Test mode DTC C1573 is cleared.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FOR DTC (SFI SYSTEM)
2.CHECK FOR DTC (SFI SYSTEM)
a.

Check whether DTCs for the ECM are output.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTCs for ECM are not output.


Result:
Result Proceed to
OK A
NG 1NR-FE B
2NR-FE C




A

3.READ VALUE USING GTS (ENGINE REVOLUTION)

B

GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

C

GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

3.READ VALUE USING GTS (ENGINE REVOLUTION)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Check the values indicated on the GTS and on the tachometer.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Revolution Engine speed Min.: 0 rpm
Max.: 8160 rpm
No significant fluctuation. The engine is running at a constant speed.
Chassis > EMPS > Data List
Tester Display
Engine Revolution
50003 13 8
OK:

Abnormal change in engine speed does not occur when idling.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the F12 power steering ECU assembly connector.


b.

Disconnect the F130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-5 (TACH) - F130-11 (TACH) Always Below 1 Ω
F12-5 (TACH) or F130-11 (TACH) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT POWER STEERING ECU ASSEMBLY (TACH SIGNAL)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.INSPECT POWER STEERING ECU ASSEMBLY (TACH SIGNAL)
a.
C285253C02
1.104,1.823 1.438,2.094 0.333,0.271 1.229,2.552 0.896,2.031 true 2.781,3.781 3.24,3.979 0.458,0.198 10 false GND 1.156,1.875 1.615,2.073 0.458,0.198 10 false F12 1.281,2.469 1.906,2.667 0.625,0.198 10 false TACH 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Start the engine.


c.

Check the waveform of the power steering ECU assembly using an oscilloscope while idling the engine.

OK:
Tester Connection Condition Specified Condition
F12-5 (TACH) - Body ground Idling Correct waveform is as shown


Tool Setting
Item Contents
Tool Setting 5 V/DIV., 10 ms./DIV.

HINT:

The wavelength becomes shorter as the engine speed increases.


Result:
Result Proceed to
OK A
NG 1NR-FE B
2NR-FE C




A

REPLACE POWER STEERING ECU ASSEMBLY

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)