Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.10–2017.10
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the meter CPU receives engine coolant temperature signals from the ECM using the CAN communication system (CAN V Bus). The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E143765E85
0.625,3.083 2.021,3.417 1.396,0.333 10 false ECM 2.927,3.156 3.021,3.344 0.094,0.188 10 false : 3.01,3.177 4.656,3.531 1.646,0.354 10 false CAN Communication Line 5.302,3.073 7.115,3.677 1.813,0.604 10 false Combination Meter Assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

HINT:

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the SFI system.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (COOLANT TEMP)

B

2.PERFORM ACTIVE TEST USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Coolant Cool Water temperature cool indicator light OFF or ON -
Indicat. Lamp Coolant Hot Water temperature hot warning light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Coolant Cool
50004 122 17
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Coolant Hot
50004 122 18
OK:

Value selected during Active Test is displayed.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
OK:

Vehicle's coolant temperature and tester value are the same.



Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FOR DTC

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 1NR-FE) B
SFI system DTCs are output. (for 2NR-FE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C