Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM D

NETWORKING  CAN COMMUNICATION SYSTEM  DIAGNOSIS SYSTEM  


ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

Combination meter assembly


ii.

Certification ECU (Smart key ECU assembly)*1


iii.

Airbag ECU assembly*2


iv.

Air conditioning amplifier assembly


v.

Brake actuator assembly*3


vi.

Spiral cable with sensor sub-assembly*4


vii.

ECM




*1: w/ Smart Entry and Start System

*2: w/ Airbag System

*3: w/ ABS

*4: w/ VSC


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION


a.

The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed on the vehicle.

ECU / Sensor Name GTS Display Applicability
ECM ECM (Engine) Installed on all vehicles
Brake actuator assembly Skid Control (ABS/VSC/TRC) Vehicles with ABS
Air conditioning amplifier assembly Air Conditioning Amplifier Installed on all vehicles
Airbag ECU assembly Airbag Vehicles with airbag system
Certification ECU (Smart key ECU assembly) Certification (Smart) Vehicles with smart entry and start system
Spiral cable with sensor sub-assembly Spiral cable (Steering Angle Sensor) Vehicles with VSC
Combination meter assembly Combination Meter Installed on all vehicles

HINT:

The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.




CAN BUS CHECK


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.


a.

Using the GTS, select the CAN Bus Check screen.

NOTICE:
·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)

·

In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM.



HINT:

Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.


Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.




b.

Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

HINT:
·

If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.

·

If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.





HOW TO INTERPRET CAN BUS CHECK SCREEN


a.

When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

NOTICE:

The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.


HINT:
·

When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.

·

Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select CAN bus check. Then observe the communication status of each ECU on the screen.




b.

If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.

Example: Open in both CAN branch lines of ECU B on the V bus

C240692C13
5.885,0.083 6.146,0.344 0.26,0.26 10 *a 0.396,3.229 1.063,3.615 0.667,0.385 10 DLC3 5.885,0.563 6.146,0.823 0.26,0.26 10 *b 5.469,1.052 5.729,1.313 0.26,0.26 10 *c 5.49,1.573 5.75,1.833 0.26,0.26 10 *d 5.573,2.073 5.833,2.333 0.26,0.26 10 *e 4.281,3.083 4.542,3.344 0.26,0.26 10 *f
*a V Bus *b Sub bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color changes to red or yellow *f CAN Bus Check screen


HINT:

When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



c.
C240693C08
0.24,1.719 0.479,1.917 0.24,0.198 10 *a 2.885,2.427 3.125,2.625 0.24,0.198 10 *b 1.031,2.448 1.271,2.646 0.24,0.198 10 *c
*a Background color periodically changes to yellow or red
*b Not displayed or background color is yellow or red
*c Not displayed


If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or a sensor which is not displayed) is suspected.

Example: Open in a CAN branch line for ECU D on the V bus

Explanation of CAN Bus Check Screen
Bus Type Background Color Connection Status
V Bus White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that does not have history of connected ECUs)*2
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
Not displayed Communication stop has continued since the start of the CAN bus check.*1
Sub bus
(gateway function equipped ECU that has history of connected ECUs)*3
White Communication has been normal since the start of the CAN bus check.
Yellow Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
Red Currently not communicating (either of the following):
·

Communication stop has continued since the start of the CAN bus check.

·

Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.


Not displayed Either of the following:
·

If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.

·

If no ECUs are connected to the sub bus, "There is no system found on the Communication Bus" will be displayed.



HINT:
·

Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.

·

*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.

·

*2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.

·

*3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.

·

The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.

·

The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.




d.
C240694C08
0.24,1.74 0.458,1.969 0.219,0.229 10 *a 2.875,2.438 3.094,2.667 0.219,0.229 10 *a
*a Not displayed or background color changes to red


If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.

Example: Open in both CAN branch lines of ECU C on the V bus

HINT:
·

In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.

·

If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.

·

The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.




e.
C240695C08
3,1.531 3.188,1.708 0.188,0.177 10 *a
*a Background color changes to red


If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.

Example: Open in both CAN branch lines of ECU G on the sub bus

HINT:
·

A communication error in a sub bus does not affect the V bus or other buses.

·

When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)




f.

If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU A and B are not displayed or their background color changes to red.)

C240696C10
0.385,3.219 0.906,3.49 0.521,0.271 10 DLC3 5.844,0.083 6.125,0.313 0.281,0.229 10 *a 5.844,0.552 6.125,0.781 0.281,0.229 10 *b 5.469,1.042 5.75,1.271 0.281,0.229 10 *c 5.469,1.542 5.75,1.771 0.281,0.229 10 *d 5.563,2.073 5.844,2.302 0.281,0.229 10 *e 4.302,3.042 4.583,3.271 0.281,0.229 10 *f
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color is red *f CAN Bus Check screen


HINT:

If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



g.

If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.

(In this case, ECU I and J are not displayed or their background color changes to red.)

C240697C08
0.375,3.229 0.813,3.448 0.438,0.219 10 DLC3 5.844,0.083 6.135,0.375 0.292,0.292 10 *a 5.583,2.073 5.865,2.302 0.281,0.229 10 *e 5.854,0.542 6.135,0.771 0.281,0.229 10 *b 5.49,1.031 5.771,1.26 0.281,0.229 10 *c 5.49,1.552 5.771,1.781 0.281,0.229 10 *d 4.323,3.063 4.604,3.292 0.281,0.229 10 *f 2.719,1.438 3,1.667 0.281,0.229 10 *g
*a V Bus *b Sub Bus
*c Terminating Resistor *d Location of malfunction
*e Not displayed or background color is red *f CAN Bus Check screen
*g Gateway function equipped ECU - -



h.
C240698C09
0.323,0.083 0.594,0.313 0.271,0.229 10 false *a 0.323,2.271 0.948,2.708 0.625,0.438 10 false *b 2.885,1.844 3.333,2.188 0.448,0.344 10 false *c 0.323,1.844 0.813,2.198 0.49,0.354 10 false *c 2.865,4.052 3.313,4.417 0.448,0.365 10 false *c
*a When any of the following malfunctions occur on the V bus
*b When any of the following malfunctions occur on a sub bus
*c Not displayed


When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.

Details of Malfunction
Short between CAN lines (CANH and CANL)
Short between a CAN line (CANH or CANL) and +B
Short between a CAN line (CANH or CANL) and ground
Open in a CAN main bus line

HINT:
·

When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).

·

When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.

·

A communication error in a sub bus does not affect the V bus or other buses.

·

The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.





HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


a.

If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

HINT:

Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.


i.

If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.

C240702C05
0.719,0.167 1.521,0.385 0.802,0.219 10 Output from 2.198,0.167 3,0.385 0.802,0.219 10 Output DTC 4.49,0.167 5.438,0.385 0.948,0.219 10 Tester display 6.917,0.292 7.156,0.479 0.24,0.188 10 : *a
*a Items to be checked - -


NOTICE:
·

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

·

Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)



HINT:

As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



ii.

If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.

C240703C06
6.875,0.302 7.135,0.49 0.26,0.188 10 : *a 4.448,0.167 5.365,0.385 0.917,0.219 10 Tester display 2.198,0.167 3.052,0.375 0.854,0.208 10 Output DTC 0.74,0.167 1.552,0.375 0.813,0.208 10 Output from
*a Items to be checked - -


NOTICE:

This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.


HINT:
·

If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.

·

When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.





b.

To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.

C240704C09
3.583,0.396 3.792,0.396 false 1.365,1.813 1.052,2.375 1.052,2.375 0.885,2.375 false 4.833,0.333 5.427,0.74 0.594,0.406 10 : *d 3.854,0.313 4.188,0.698 0.333,0.385 10 *f 3.677,0.958 4.083,1.323 0.406,0.365 10 *c 0.427,1.729 0.792,2.073 0.365,0.344 10 *b 0.688,2.281 1.073,2.604 0.385,0.323 10 *e 0.896,2.76 2.292,3.25 1.396,0.49 10 Output from 2.49,2.771 3.792,3.323 1.302,0.552 10 Output DTC 4.698,2.76 6.104,3.219 1.406,0.458 10 Tester display 1.125,4.521 1.708,4.76 0.583,0.24 10 : *a
*a Items to be checked *b ECM
*c Gateway function equipped ECU *d Location of malfunction
*e V Bus *f Sub bus


NOTICE:

This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.


HINT:
·

As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.

·

When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.




c.

When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

·

Short between CAN lines (CANH and CANL)

·

Short between a CAN line (CANH or CANL) and ground

·

Short between a CAN line (CANH or CANL) and +B

·

Open in a CAN branch line (CANH or CANL) of an ECU or sensor

·

Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor




DTC TABLE BY ECU


HINT:
·

In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.

·

If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.



a.

ECM / GTS Display "Engine and ECT"

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

This ECU uses the CAN communication system for DTC communication.


ECM / GTS Display "Engine and ECT"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0129 Lost Communication with Brake System Control Module The ECM does not receive data from the brake actuator assembly for 2.22 seconds or more. Both conditions are met:
·

The ignition switch is ON for 2.1 seconds or more.

·

The power source voltage of the ECM is 10.5 V or more.


Turn the ignition switch to ON and wait 4.32 seconds or more. MIL illuminates. DTC is stored until it is cleared using the GTS.


b.

Brake Actuator Assembly (w/ ABS with VSC) / GTS Display "ABS/VSC/TRC"

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

This ECU uses the CAN communication system for DTC communication.


Brake Actuator Assembly / GTS Display "ABS/VSC/TRC"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus Off One of the following conditions is met:
·

The response sent to the brake actuator assembly from the spiral cable with sensor sub-assembly is invalid for 1 second or more.

·

The response sent to the brake actuator assembly from the airbag ECU assembly is invalid for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly from the airbag ECU assembly is invalid at least once within 5 seconds.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly from the spiral cable with sensor sub-assembly is invalid at least once within 5 seconds.

·

The brake actuator assembly cannot send or receive data (the bus is off) 10 times consecutively.


Both conditions are met:
·

The ignition switch is ON for 1 second or more.

·

The power source voltage of the brake actuator assembly is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 61 seconds.
·

ABS warning light illuminates.

·

SLIP indicator light illuminates.

·

Brake warning light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0100 Lost Communication With ECM/PCM "A" The response sent to the brake actuator assembly from the ECM is invalid for 2 seconds or more. All conditions are met:
·

The ignition switch is ON for 1 second or more.

·

Vehicle speed is 15 km/h (9 mph) or more.

·

The power source voltage of the brake actuator assembly is between 10 and 17.4 V.


Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.
U0124 Lost Communication With Lateral Acceleration Sensor Module Either condition is met:
·

The brake actuator assembly does not receive data from the airbag ECU assembly for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly from the airbag ECU assembly is invalid at least once within 5 seconds.


Both conditions are met:
·

The ignition switch is ON for 1 second or more.

·

The power source voltage of the brake actuator assembly is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 61 seconds.
·

ABS warning light illuminates.

·

SLIP indicator light illuminates.


The DTC remains stored until it is cleared using the GTS.
U0126 Lost Communication With Steering Angle Sensor Module Either condition is met:
·

The brake actuator assembly does not receive data from the spiral cable with sensor sub-assembly for 1 second or more.

·

The following condition occurs 10 times consecutively within 60 seconds: The response sent to the brake actuator assembly from the spiral cable with sensor sub-assembly is invalid at least once within 5 seconds.


Both conditions are met:
·

The ignition switch is ON for 1 second or more.

·

The power source voltage of the brake actuator assembly is between 10 and 17.4 V.


Turn the ignition switch to ON and wait at least 61 seconds. SLIP indicator light illuminates. The DTC remains stored until it is cleared using the GTS.


c.

Brake Actuator Assembly (w/ ABS without VSC) / GTS Display "ABS/VSC/TRC"

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

This ECU uses the CAN communication system for DTC communication.


Brake Actuator Assembly / GTS Display "ABS/VSC/TRC"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0073 Control Module Communication Bus OFF The +BS terminal voltage is between 10.0 and 17.4 V and bus off is judged for 0.1 seconds or more. Both conditions are met:
·

The ignition switch is ON for 1 second or more.

·

The power source voltage of the brake actuator assembly (+BS terminal voltage) is between 10.0 and 17.4 V.


Turn the ignition switch to ON and check that the initial light check illumination turns off, and then wait at least 3 seconds. ABS warning light illuminates. DTC is stored until it is cleared using the GTS.


d.

Combination Meter Assembly / GTS Display "Combination Meter"

Body Electrical > Combination Meter > Trouble Codes
50001 122
HINT:

This ECU uses the CAN communication system for DTC communication.


Combination Meter Assembly / GTS Display "Combination Meter"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM / PCM "A"
Multi-information Display
The combination meter assembly does not receive data from the ECM for 2 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 2 seconds. - DTC is stored until it is cleared using the GTS.
U0129 Lost Communication with Skid Control ECU The combination meter assembly does not receive data from the brake actuator assembly for 3 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 3 seconds. - DTC is stored until it is cleared using the GTS.
U0151 Lost Communication with Airbag ECU The combination meter assembly does not receive data from the airbag ECU assembly for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the combination meter assembly is 9.5 V or more.


Turn the ignition switch to ON and wait at least 10 seconds. SRS warning light illuminates. DTC is stored until it is cleared using the GTS.


e.

Airbag ECU Assembly (w/ Airbag System)

HINT:

The airbag ECU assembly is connected to the CAN communication system, but the airbag ECU assembly does not store or output CAN communication DTCs.



f.

Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

Body Electrical > Air Conditioner > Trouble Codes
50001 121
HINT:

This ECU uses the CAN communication system for DTC communication.


Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or more.


Turn the ignition switch to ON and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Combination Meter The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. Both conditions are met:
·

The ignition switch is ON.

·

The power source voltage of the air conditioning amplifier assembly is 10 V or more.


Turn the ignition switch to ON and wait at least 5 seconds. - DTC is stored until it is cleared using the GTS.


g.

Certification ECU (Smart Key ECU Assembly) (w/ Smart Entry and Start System) / GTS Display "Entry&Start"

HINT:

This ECU uses the CAN communication system for DTC communication.


Body Electrical > Entry&Start > Trouble Codes
50001 125
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
DTC Detection Item DTC Detection Condition DTC Detection Pre-condition DTC Check Procedure Warning Indication in Meter DTC Storage Method
U0100 Lost Communication with ECM / PCM The certification ECU (smart key ECU assembly) does not receive data from the ECM for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON for 10 seconds or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the ignition switch to ON and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.
U0155 Lost Communication with Combination Meter The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for 10 seconds or more. Both conditions are met:
·

The ignition switch is ON for 10 seconds or more.

·

The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more.


Turn the ignition switch to ON and wait at least 20 seconds. - DTC is stored until it is cleared using the GTS.


h.

Spiral Cable with Sensor Sub-assembly (w/ VSC)

HINT:

The spiral cable with sensor sub-assembly is connected to the CAN communication system, but the spiral cable with sensor sub-assembly does not store or output CAN communication DTCs.




DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)


a.

Regarding a past communication error of an ECU or sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.

HINT:
·

Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.

·

Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).

·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 5 to 7) first.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.



for LHD:
Trouble Mode (Open in One CAN Branch Line)
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode
Click here(Click here)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Air Conditioning Amplifier Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ▲ ▲ X
U0155 ▲ ▲ X
ECM U0129 ▲ X ▲
Certification ECU (Smart Key ECU Assembly) U0100 ▲ ▲ ▲
U0155 ▲ ▲ ▲
Combination Meter Assembly U0100 ▲ ▲ ▲
U0129 ▲ X ▲
U0151 X ▲ ▲
Spiral Cable with Sensor Sub-assembly - - - -
Brake Actuator Assembly*1 U0100 ▲ X ▲
U0124 X X ▲
U0126 ▲ X ▲

for LHD:
Trouble Mode (Open in One CAN Branch Line)
Output ECU Output DTC Certification ECU Communication Stop Mode
Click here(Click here)
Steering Angle Sensor Communication Stop Mode
Click here(Click here)
DLC3
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ▲ ▲ ▲
U0155 ▲ ▲ ▲
ECM U0129 ▲ ▲ ▲
Certification ECU (Smart Key ECU Assembly) U0100 X ▲ ▲
U0155 X ▲ ▲
Combination Meter Assembly U0100 ▲ ▲ ▲
U0129 ▲ ▲ ▲
U0151 ▲ ▲ ▲
Spiral Cable with Sensor Sub-assembly - - - -
Brake Actuator Assembly*1 U0100 ▲ ▲ ▲
U0124 ▲ ▲ ▲
U0126 ▲ X ▲

HINT:
·

*1: U0073 may be stored when communication is lost.

·

X: DTC is likely to be output.

·

▲: DTC is not likely to be output.

·

-: DTC is not output.



for LHD:
Trouble Mode (Open in Both CAN Branch Lines)
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode
Click here(Click here)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Air Conditioning Amplifier Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - ○
U0155 - - ○
ECM U0129 - ○ -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0155 - - -
Combination Meter Assembly U0100 - - -
U0129 - ○ -
U0151 ○ - -
Spiral Cable with Sensor Sub-assembly - - - -
Brake Actuator Assembly*1 U0100 - ○ -
U0124 ○ ○ -
U0126 - ○ -

for LHD:
Trouble Mode (Open in Both CAN Branch Lines)
Output ECU Output DTC Certification ECU Communication Stop Mode
Click here(Click here)
Steering Angle Sensor Communication Stop Mode
Click here(Click here)
DLC3
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - -
U0155 - - -
ECM U0129 - - -
Certification ECU (Smart Key ECU Assembly) U0100 ○ - -
U0155 ○ - -
Combination Meter Assembly U0100 - - -
U0129 - - -
U0151 - - -
Spiral Cable with Sensor Sub-assembly - - - -
Brake Actuator Assembly*1 U0100 - - -
U0124 - - -
U0126 - ○ -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.



for LHD:
Trouble Mode (Open in One CAN Main Bus Line)
Output ECU Output DTC ECM Communication Stop Mode
Click here(Click here)
Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - -
Air Conditioning Amplifier Assembly U0100 X ▲
U0155 ▲ X
ECM U0129 X ▲
Certification ECU (Smart Key ECU Assembly) U0100 X ▲
U0155 ▲ X
Combination Meter Assembly U0100 X X
U0129 ▲ X
U0151 ▲ X
Spiral Cable with Sensor Sub-assembly - ▲ ▲
Brake Actuator Assembly*1 U0100 X ▲
U0124 ▲ ▲
U0126 ▲ ▲

HINT:
·

*1: U0073 may be stored when communication is lost.

·

X: DTC is likely to be output.

·

▲: DTC is not likely to be output.

·

-: DTC is not output.



for LHD:
Trouble Mode (Open in Both CAN Main Bus Lines)
Output ECU Output DTC ECM Communication Stop Mode
Click here(Click here)
Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - -
Air Conditioning Amplifier Assembly U0100 ○ -
U0155 - ○
ECM U0129 ○ -
Certification ECU (Smart Key ECU Assembly) U0100 ○ -
U0155 - ○
Combination Meter Assembly U0100 ○ ○
U0129 - ○
U0151 - ○
Spiral Cable with Sensor Sub-assembly - - -
Brake Actuator Assembly*1 U0100 ○ -
U0124 - -
U0126 - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.



for LHD:
Trouble Mode (CAN Bus Line Short Circuit) Trouble Mode (CAN Bus Line Short to GND)
Output ECU Output DTC CANH to CANL CANH to GND CANL to GND
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ ○
U0155 ○ ○ ○
ECM U0129 ○ ○ ○
Certification ECU (Smart Key ECU Assembly) U0100 ○ ○ ○
U0155 ○ ○ ○
Combination Meter Assembly U0100 ○ ○ ○
U0129 ○ ○ ○
U0151 ○ ○ ○
Brake Actuator Assembly U0073 ○ ○ ○
Spiral Cable with Sensor Sub-assembly - - - -
Brake Actuator Assembly*1 U0100 ○ ○ ○
U0124 ○ ○ ○
U0126 ○ ○ ○

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.



for RHD:
Trouble Mode (Open in One CAN Branch Line)
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode
Click here(Click here)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Air Conditioning Amplifier Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ▲ ▲ X
U0155 ▲ ▲ X
ECM U0129 ▲ X ▲
Certification ECU (Smart Key ECU Assembly) U0100 ▲ ▲ ▲
U0155 ▲ ▲ ▲
Combination Meter Assembly U0100 ▲ ▲ ▲
U0129 ▲ X ▲
U0151 X ▲ ▲
Brake Actuator Assembly*1 - - - -

for RHD:
Trouble Mode (Open in One CAN Branch Line)
Output ECU Output DTC Certification ECU Communication Stop Mode
Click here(Click here)
DLC3
V Bus Airbag ECU Assembly - - -
Air Conditioning Amplifier Assembly U0100 ▲ ▲
U0155 ▲ ▲
ECM U0129 ▲ ▲
Certification ECU (Smart Key ECU Assembly) U0100 X ▲
U0155 X ▲
Combination Meter Assembly U0100 ▲ ▲
U0129 ▲ ▲
U0151 ▲ ▲
Brake Actuator Assembly*1 - - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

X: DTC is likely to be output.

·

▲: DTC is not likely to be output.

·

-: DTC is not output.



for RHD:
Trouble Mode (Open in Both CAN Branch Lines)
Output ECU Output DTC Center Airbag Sensor Communication Stop Mode
Click here(Click here)
Brake Actuator (Skid Control ECU) Communication Stop Mode
Click here(Click here)
Air Conditioning Amplifier Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 - - ○
U0155 - - ○
ECM U0129 - ○ -
Certification ECU (Smart Key ECU Assembly) U0100 - - -
U0155 - - -
Combination Meter Assembly U0100 - - -
U0129 - ○ -
U0151 ○ - -
Brake Actuator Assembly*1 - - - -

for RHD:
Trouble Mode (Open in Both CAN Branch Lines)
Output ECU Output DTC Certification ECU Communication Stop Mode
Click here(Click here)
DLC3
V Bus Airbag ECU Assembly - - -
Air Conditioning Amplifier Assembly U0100 - -
U0155 - -
ECM U0129 - -
Certification ECU (Smart Key ECU Assembly) U0100 ○ -
U0155 ○ -
Combination Meter Assembly U0100 - -
U0129 - -
U0151 - -
Brake Actuator Assembly*1 - - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.



for RHD:
Trouble Mode (Open in One CAN Main Bus Line)
Output ECU Output DTC ECM Communication Stop Mode
Click here(Click here)
No. 1 CAN Junction Connector to No. 2 CAN Junction Connector Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 X X ▲
U0155 ▲ ▲ X
ECM U0129 X ▲ ▲
Certification ECU (Smart Key ECU Assembly) U0100 X X ▲
U0155 ▲ ▲ X
Combination Meter Assembly U0100 X X X
U0129 ▲ X X
U0151 ▲ ▲ X
Brake Actuator Assembly*1 - - - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

X: DTC is likely to be output.

·

▲: DTC is not likely to be output.

·

-: DTC is not output.



for RHD:
Trouble Mode (Open in Both CAN Main Bus Lines)
Output ECU Output DTC ECM Communication Stop Mode
Click here(Click here)
No. 1 CAN Junction Connector to No. 2 CAN Junction Connector Combination Meter ECU Communication Stop Mode
Click here(Click here)
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ -
U0155 - - ○
ECM U0129 ○ - -
Certification ECU (Smart Key ECU Assembly) U0100 ○ ○ -
U0155 - - ○
Combination Meter Assembly U0100 ○ ○ ○
U0129 - ○ ○
U0151 - - ○
Brake Actuator Assembly*1 - - - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.



for RHD:
Trouble Mode (CAN Bus Line Short Circuit) Trouble Mode (CAN Bus Line Short to GND)
Output ECU Output DTC CANH to CANL CANH to GND CANL to GND
V Bus Airbag ECU Assembly - - - -
Air Conditioning Amplifier Assembly U0100 ○ ○ ○
U0155 ○ ○ ○
ECM U0129 ○ ○ ○
Certification ECU (Smart Key ECU Assembly) U0100 ○ ○ ○
U0155 ○ ○ ○
Combination Meter Assembly U0100 ○ ○ ○
U0129 ○ ○ ○
U0151 ○ ○ ○
Brake Actuator Assembly U0073 ○ ○ ○
Brake Actuator Assembly*1 - - - -

HINT:
·

*1: U0073 may be stored when communication is lost.

·

○: DTC is output.

·

-: DTC is not output.





CAN BUS WAVEFORMS


C230845E13
4.729,0.25 4.417,0.896 true 4.458,0.875 4.406,0.917 4.406,0.917 4.406,0.865 false 6.625,3.74 5.708,2.635 true 5.729,2.74 5.708,2.635 5.708,2.635 5.781,2.646 false 4.042,3.677 5.042,2.531 true 5.042,2.635 5.052,2.521 5.052,2.521 4.958,2.542 false 2.188,0.667 2.698,0.167 2.698,0.167 2.865,0.167 false 4.396,4.365 4.573,4.365 4.573,4.365 5.51,3.667 false 5.281,3.063 5.844,3.365 0.563,0.302 10 false ECU 3.365,3.063 3.927,3.365 0.563,0.302 10 false ECU 1.698,3.063 2.26,3.365 0.563,0.302 10 false DLC3 1.427,4.781 4.021,5.302 2.594,0.521 10 false : CAN Main Bus Line (CANH) 1.448,5.229 4.167,5.958 2.719,0.729 10 false : CAN Main Bus Line (CANL) 1.49,5.823 3.802,6.365 2.313,0.542 10 false : CAN Branch Line (CANH) 1.5,6.26 3.708,6.688 2.208,0.427 10 false : CAN Branch Line (CANL) 3.563,4.271 4.531,4.563 0.969,0.292 10 false CAN Branch 2.521,3.719 5.052,4.208 2.531,0.49 10 false Open in CAN Branch Line (CANL) 5.813,3.802 7.156,4.563 1.344,0.76 10 false Open in CAN Branch Line (CANH) 4.771,0.156 7.125,0.729 2.354,0.573 10 false Open in CAN Main Bus Line (CANH) 2.927,0.083 4.146,0.469 1.219,0.385 10 false CAN Main Bus

HINT:
·

This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)

·

When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first (Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). If no problems are found, check the following waveforms.

·

If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).

·

Wiggle the connector and wire harness to check if the waveform changes.



a.

CAN bus waveforms (Group 1)

i.
C265973E06
0.5,0.417 0.906,0.781 true 0.5,1.583 0.917,1.167 true 0.094,0.333 0.708,0.531 0.615,0.198 10 false CANH 0.135,1.552 0.75,1.75 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.708,0.25 3.427,0.448 0.719,0.198 10 false 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 false GND

Normal waveform


ii.
C265974E02
1.5,1.583 1.969,1.104 true 1.5,0.5 1.969,0.792 true 1.094,0.417 1.708,0.615 0.615,0.198 10 false CANH 1.115,1.5 1.729,1.698 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 false GND 2.667,0.24 3.354,0.417 0.688,0.177 10 false 1 V/DIV.

Open in both of the lines (CANH and CANL) of a CAN branch

HINT:
·

Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)

·

Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.




iii.
C265975E02
1.292,0.917 0.51,0.448 true 0.521,1.385 1.063,0.969 true 0.094,0.385 0.708,0.583 0.615,0.198 10 false CANH 0.156,1.323 0.771,1.521 0.615,0.198 10 false CANL 1.344,1.917 2.875,2.115 1.531,0.198 10 false 50 μs/DIV. 2.729,0.271 3.354,0.479 0.625,0.208 10 false 1 V/DIV. 2.938,1.385 3.396,1.583 0.458,0.198 10 false GND

Short between the CAN bus lines (CANH and CANL)

HINT:
·

Waveforms disappear.

·

If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.





b.

CAN bus waveforms (reference) (Group 2)

NOTICE:

The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.


i.
C265976E02
0.938,0.76 0.531,0.448 true 0.51,1.531 0.844,1.167 true 0.115,0.375 0.729,0.573 0.615,0.198 10 false CANH 0.146,1.469 0.76,1.667 0.615,0.198 10 false CANL 1.313,1.927 2.844,2.125 1.531,0.198 10 false 50 μs/DIV. 2.708,0.281 3.344,0.5 0.635,0.219 10 false 1 V/DIV. 2.969,1.385 3.427,1.583 0.458,0.198 10 false GND

Open in a CAN branch line (CANH)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




ii.
C265977E02
0.531,1.396 0.906,1.146 true 0.531,0.406 0.833,0.74 true 0.115,0.344 0.729,0.542 0.615,0.198 10 false CANH 0.156,1.344 0.771,1.542 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.281 3.417,0.51 0.719,0.229 10 false 1 V/DIV. 2.958,1.385 3.417,1.583 0.458,0.198 10 false GND

Open in a CAN branch line (CANL)

HINT:
·

An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.

·

Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.




iii.
C265978E02
0.51,0.417 0.938,0.708 true 0.542,1.438 0.938,1.156 true 0.083,0.344 0.698,0.542 0.615,0.198 10 false CANH 0.146,1.365 0.76,1.563 0.615,0.198 10 false CANL 1.323,1.927 2.854,2.125 1.531,0.198 10 false 50 μs/DIV. 2.698,0.281 3.281,0.521 0.583,0.24 10 false 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 false GND

Open in a CAN main bus line (CANH)

HINT:
·

Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.

·

Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.

·

An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.




iv.
C265979E02
0.542,1.813 1.083,1.531 true 1.063,1.333 0.531,0.906 true 0.115,0.844 0.729,1.042 0.615,0.198 10 false CANH 0.167,1.75 0.781,1.948 0.615,0.198 10 false CANL 1.313,1.917 2.844,2.115 1.531,0.198 10 false 50 μs/DIV. 2.719,0.302 3.375,0.552 0.656,0.25 10 false 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 false GND

Short between a CAN bus line (CANH) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.

·

A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.




v.
C265980E02
0.521,1.708 0.948,1.385 true 0.531,0.469 1.021,0.708 true 0.125,0.406 0.74,0.604 0.615,0.198 10 false CANH 0.156,1.646 0.771,1.844 0.615,0.198 10 false CANL 1.333,1.917 2.865,2.115 1.531,0.198 10 false 50 μs/DIV. 2.698,0.271 3.292,0.531 0.594,0.26 10 false 1 V/DIV. 2.969,1.375 3.427,1.573 0.458,0.198 10 false GND

Short between a CAN bus line (CANL) and ground

HINT:
·

Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connector or when disconnecting ECUs or sensors.

·

A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.






DATA SENDING/RECEIVING TABLE


a.

Data sending/receiving table

HINT:

If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.


Data Content Data Detected and Sent by Data Received from
(Can be Checked in Data List)
Data Received
(Cannot be Checked in Data List)
Relevant Data List Item
[Selected System]
Engine speed ECM
·

Brake actuator assembly*3

·

Combination meter assembly

·

Certification ECU (Smart key ECU assembly)*4


·

Airbag ECU assembly*5

·

Air conditioning amplifier assembly


·

Engine Speed [Engine and ECT]

·

Engine Revolutions [ABS/VSC/TRC]*3

·

Engine Rpm [Combination Meter]

·

Engine Speed [Starting Control]*4


Accelerator position ECM Brake actuator assembly*3 -
·

Accelerator Position [Engine and ECT]

·

Accelerator Opening Angle % [ABS/VSC/TRC]*3


Shift position ECM Certification ECU (Smart key ECU assembly)*4
·

Airbag ECU assembly*5

·

Combination meter assembly


·

Neutral Position SW Signal [Engine and ECT]

·

Shift P Signal [Power Source Control]*4


Engine coolant temperature ECM
·

Air conditioning amplifier assembly

·

Combination meter assembly


-
·

Coolant Temp [Engine and ECT]

·

Engine Coolant Temp [Air Conditioner]

·

Coolant Temperature [Combination Meter]


Vehicle speed Brake actuator assembly*6 Combination meter assembly*2
·

ECM

·

Airbag ECU assembly*5


·

Vehicle Speed [ABS/VSC/TRC]*6

·

Vehicle Speed Meter [Combination Meter]


Combination meter assembly*2 Certification ECU (Smart key ECU assembly)*4 Air conditioning amplifier assembly
·

Vehicle Speed Meter [Combination Meter]

·

Vehicle Speed Signal [Power Source Control]*4


Wheel speed Brake actuator assembly*6 - ECM
·

FR Wheel Speed [ABS/VSC/TRC]*6

·

FL Wheel Speed [ABS/VSC/TRC]*6

·

RR Wheel Speed [ABS/VSC/TRC]*6

·

RL Wheel Speed [ABS/VSC/TRC]*6


Ambient temperature Air conditioning amplifier assembly ECM -
·

Ambient Temp Sensor [Air Conditioner]

·

Ambient Temp for A/C [Engine and ECT]


Brake actuator assembly power source voltage*1 Brake actuator assembly*6 - - IG1 Voltage Value [ABS/VSC/TRC]*6
Driver door touch sensor*1 Certification ECU (Smart key ECU assembly)*4 - - D-Door Touch Sensor [Entry&Start]*4
ECM power source voltage*1 ECM - - Battery Voltage [Engine and ECT]
Combination meter assembly power source voltage*1 Combination meter assembly - - +B Voltage Value [Combination Meter]
Solar sensor*1 Air conditioning amplifier assembly*7 - - Solar Sensor (D Side) [Air Conditioner]*7

*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.

*2: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly and sends the signal to other ECUs.

*3: w/ VSC

*4: w/ Smart Entry and Start System

*5: w/ Airbag System

*6: w/ ABS

*7: w/ Automatic Air Conditioning System



b.

Details of relevant Data List items (Selected system: Engine and ECT)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N (neutral), the A/C switch (if equipped) should be off and all accessory switches should be off.



i.

Warm up the engine.


ii.

Turn the A/C switch off (w/ Air Conditioning System).


iii.

Turn the ignition switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Enter the following menus: Powertrain / Engine and ECT / Data List.


viii.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed
·

Stored as Freeze Frame Data: Yes

·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

·

To accurately confirm whether the vehicle was stopped or not, use "SPD (NO)", which is the A/T or CVT output speed (for CVT models).



Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 600 to 700 rpm: Idling*1
680 to 780 rpm: Idling*2
550 to 650 rpm: Idling*3
·

Stored as Freeze Frame Data: Yes

·

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.


Coolant Temp Coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up
·

Stored as Freeze Frame Data: Yes

·

This is the engine coolant temperature.


HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.

·

Check if the engine overheats when the value indicates 140°C (284°F).



Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V: Idling
·

Stored as Freeze Frame Data: Yes

·

If 11 V or less, characteristics of some electrical components may change.


Accelerator Position Accelerator pedal position Min.: 0%, Max.: 399.9% Actual accelerator pedal position
·

Stored as Freeze Frame Data: No

·

The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.


HINT:

If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Neutral Position SW Signal Park/Neutral position switch status*4 ON or OFF ON: Shift lever in P or N Stored as Freeze Frame Data: Yes
Ambient Temp for A/C Ambient temperature for A/C Min.: -40°C (-40°F), Max.: 215°C (419°F) - Stored as Freeze Frame Data: Yes

*1: for 1NR-FE with CVT

*2: for 2NR-FE with CVT

*3: for Manual Transaxle

*4: for CVT




c.

Details of relevant Data List items (Selected system: Power Source Control)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P*1 ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-

*1: for CVT



d.

Details of relevant Data List items (Selected system: ABS/VSC/TRC)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS on.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


vii.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Engine Revolutions Engine speed*1 Min.: 0 rpm, Max.: 65535 rpm Engine stopped:
0 rpm
When engine speed is constant:
No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle*1 Min.: 0.0%, Max.: 128.0% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
IG1 Voltage Value IG1 voltage value Min.: 0.00 V, Max.: 20.00 V Ignition switch ON: 11.00 to 14.00 V Changes in proportion to battery voltage

*1: w/ VSC




e.

Details of relevant Data List items (Selected system: Entry&Start)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:
·

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Entry&Start / Data List.


v.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Touch Sensor Driver door touch sensor (unlock sensor)*1 ON or OFF ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


*1: Data from an actual vehicle provided for reference.



f.

Details of relevant Data List items (Selected system: Combination Meter)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Warm up the engine.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS on.


vi.

Enter the following menus: Body Electrical / Combination Meter / Data List.


vii.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Engine Rpm Engine speed Min.: 0 rpm, Max.: 12750 rpm 600 to 700 rpm: Idling*1
680 to 780 rpm: Idling*2
550 to 650 rpm: Idling*3
-
Coolant Temperature Engine coolant temperature 0 to 127.5°C (0 to 261.5°F) 75 to 100°C (167 to 212°F) (After warming up engine) -
+B Voltage Value Battery voltage Min.: 0 V, Max.: 25.5 V 11 to 14 V -
Ambient Temperature Outside temperature Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) Almost the same as actual outside temperature The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

*1: for 1NR-FE with CVT

*2: for 2NR-FE with CVT

*3: for Manual Transaxle




g.

Details of relevant Data List items (Selected system: Air Conditioner)

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


v.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Solar Sensor (D Side) Cooler (solar sensor) thermistor Min.: 0
Max.: 255
Cooler (solar sensor) thermistor value increases as brightness increases -
Engine Coolant Temp Engine coolant temperature sensor Min.: 1.30°C (34.34°F)
Max.: 90.55°C (194.99°F)
Actual engine coolant temperature is displayed -