Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2016.10–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090851 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the engine switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*1).
·

Engine switch

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P*2 and the key held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.



*1: Only output while a malfunction is present.

*2: for CVT


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P*1 -

*1: for CVT


Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

E271702E03
1.552,0.75 2.01,0.948 0.458,0.198 10 false VC5 1.5,1.25 1.958,1.448 0.458,0.198 10 false TXCT 1.427,1.75 1.885,1.948 0.458,0.198 10 false CODE 1.438,2.271 1.896,2.469 0.458,0.198 10 false AGND 5.292,0.75 5.75,0.948 0.458,0.198 10 false VC5 5.292,1.25 5.75,1.448 0.458,0.198 10 false TXCT 5.292,1.802 5.75,2 0.458,0.198 10 false CODE 5.292,2.302 5.75,2.5 0.458,0.198 10 false AGND 1.958,0.635 2.167,0.833 0.208,0.198 10 false 10 1.958,1.167 2.167,1.365 0.208,0.198 10 false 7 1.958,1.677 2.167,1.875 0.208,0.198 10 false 8 1.958,2.198 2.167,2.396 0.208,0.198 10 false 6 5,0.552 5.208,0.75 0.208,0.198 10 false 20 5.042,1.052 5.292,1.25 0.25,0.198 10 false 2 5.042,1.583 5.208,1.75 0.167,0.167 10 false 1 5,2.083 5.25,2.25 0.25,0.167 10 false 24 4.958,1.26 5.333,1.51 0.375,0.25 10 false F44 4.958,0.74 5.333,0.99 0.375,0.25 10 false F44 5.25,2.833 6.833,3.583 1.583,0.75 10 false Certification ECU (Smart Key ECU Assembly) 4.958,1.781 5.333,2.031 0.375,0.25 10 false F44 4.958,2.292 5.333,2.542 0.375,0.25 10 false F43 0.833,2.833 1.208,3.083 0.375,0.25 10 false F13 0.833,3 1.875,3.25 1.042,0.25 10 false Engine Switch

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

B

3.CHECK ENGINE SWITCH (OUTPUT)
3.CHECK ENGINE SWITCH (OUTPUT)
a.

Using an oscilloscope, check the waveform.

E293555C03
1.417,0.833 1.917,1.083 0.5,0.25 1.073,2.813 1.615,2.146 true 4.521,0.26 4.177,0.552 true 1.531,0.854 1.896,1.042 0.365,0.188 10 false F13 0.719,0.688 1.031,0.885 0.313,0.198 10 false *a 3.333,0.156 3.646,0.354 0.313,0.198 10 false *b 4.573,0.167 4.885,0.365 0.313,0.198 10 false *c 3.344,2.031 3.656,2.229 0.313,0.198 10 false *d 6.51,1.344 6.917,1.552 0.406,0.208 10 false GND 6.5,3.135 6.906,3.344 0.406,0.208 10 false GND 0.865,2.865 1.479,3.063 0.615,0.198 10 false CODE
*a Component with harness connected
(Engine Switch)
*b Waveform 1
*c Waveform 2 *d Waveform 2 (detail)


Waveform 1
Item Content
Tester Connection F13-8 (CODE) ←→ Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*1

Waveform 2 (detail)
Item Content
Tester Connection F13-8 (CODE) ←→ Body ground
Tool Setting 2 V/DIV., 100 μs./DIV.
Tool Setting Engine switch off, engine switch pressed with key held near engine switch*1

HINT:

*1: Remove the key battery before performing this inspection.


OK:

Waveform is similar to that shown in the illustration



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the certification ECU (smart key ECU assembly).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output



Result:
Result Proceed to
B2784 is not output A
B2784 is output (for 1NR-FE) B
B2784 is output (for 2NR-FE) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C