Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*2):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

ECM


Either condition is met:
·

Within 10 seconds of an engine start operation being performed (with the clutch pedal depressed*1, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*1: for Manual Transaxle

*2: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

E347408E05
1.26,0.875 1.563,1.115 0.302,0.24 10 false IMI 1.604,0.75 1.906,0.99 0.302,0.24 10 false 10 1.625,1.292 1.927,1.531 0.302,0.24 10 false 9 1.219,1.406 1.521,1.646 0.302,0.24 10 false IMO 0.729,2.146 1.125,2.427 0.396,0.281 10 false ECM 0.729,1.99 1.083,2.229 0.354,0.24 10 false F130 5.5,0.76 5.802,1 0.302,0.24 10 false 4 5.49,1.302 5.792,1.542 0.302,0.24 10 false 5 5.719,0.865 6.135,1.104 0.417,0.24 10 false EFIO 5.729,1.406 6.146,1.625 0.417,0.219 10 false EFII 5.615,2.031 5.917,2.271 0.302,0.24 10 false F51 5.604,2.208 6.688,2.698 1.083,0.49 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC
a.

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output



Result:
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT ECM (TERMINAL IMO)

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

E347147C01
4.115,2.042 4.615,2.292 0.5,0.25 4.719,0.271 5.219,0.521 0.5,0.25 5.604,1.854 5.156,1.094 true 5.01,3.646 4.563,2.885 true 0.031,0.354 0.385,0.573 0.354,0.219 12 false *A 0.656,2.156 0.979,2.417 0.323,0.26 12 false *B 0.083,0.063 0.51,0.344 0.427,0.281 10 false *a 2.917,5.25 3.229,5.406 0.313,0.156 10 false *b 5.667,1.781 6.125,1.979 0.458,0.198 10 false IMO 0.958,5.146 1.417,5.344 0.458,0.198 10 false GND 5.083,3.563 5.542,3.76 0.458,0.198 10 false IMO 4.219,2.094 4.677,2.292 0.458,0.198 10 false F130 4.813,0.323 5.271,0.521 0.458,0.198 10 false F130
*A for CVT *B for Manual Transaxle
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection F130-9 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is similar to that shown in the illustration



Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

4.INSPECT ECM (TERMINAL IMI)

B

10.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

7.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

E347148C01
4.781,0.281 5.281,0.5 0.5,0.219 4.104,2.052 4.604,2.302 0.5,0.25 4.938,3.677 4.469,2.938 true 5.542,1.896 5.073,1.156 true 0.052,0.417 0.365,0.573 0.313,0.156 12 false *A 0.656,2.219 0.958,2.469 0.302,0.25 12 false *B 0.094,0.042 0.49,0.292 0.396,0.25 10 false *a 3.354,5.146 3.667,5.302 0.313,0.156 10 false *b 0.958,5.031 1.302,5.229 0.344,0.198 10 false GND 5.042,3.604 5.333,3.823 0.292,0.219 10 false IMI 5.646,1.823 5.958,2.021 0.313,0.198 10 false IMI 4.885,0.313 5.229,0.479 0.344,0.167 10 false F130 4.198,2.094 4.542,2.26 0.344,0.167 10 false F130
*A for CVT *B for Manual Transaxle
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection F130-10 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is similar to that shown in the illustration



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID

NG

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ECM
7.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

10.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.
E347141C03
1.385,0.292 1.885,0.542 0.5,0.25 2.219,1.865 1.51,1.219 true 0.104,0.094 0.417,0.333 0.313,0.24 10 false *a 1.479,0.333 2.094,0.531 0.615,0.198 10 false F130 2.281,1.823 2.74,2.021 0.458,0.198 10 false IMO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
F130-9 (IMO) - Body ground*1 Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMI stuck low (2.4 V or less) A
Terminal IMI stuck high (12 V) or Abnormal waveform B



A

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

B

7.REPLACE ECM
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
a.

Disconnect the F51 transponder key ECU assembly connector.


b.

Disconnect the F130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-5 (EFII) - F130-9 (IMO) Always Below 1 Ω
F51-5 (EFII) - Body ground Always 10 kΩ or higher
F130-9 (IMO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.REGISTER KEY
13.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C