55301
1.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
Using a nipper, cut off both ends of the 3 runner portions shown in the illustration (When installing a new one).
| *a | Runner Portion | *b | Cut Off |
Engage the 9 guides and temporarily install the instrument panel sub-assembly.
Do not damage the instrument panel sub-assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the 2 clips.
Install the 4 bolts <A>, 2 bolts <E>, bolt <D> and 2 screws <B>.
for Automatic Air Conditioning System:
Connect the cooler thermistor hose.
Engage the clamps.
Connect the connectors.
53601
2.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and the 3 guides and connect the hood lock control lever sub-assembly.
82142A
3.CONNECT INSTRUMENT PANEL WIRE
Connect the connector.
When connecting any airbag connector, take care not to damage the airbag wire harness.
58910C
4.INSTALL REAR CONSOLE BOX ASSEMBLY
55660
5.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 7 claws and the clip and install the No. 2 instrument panel register assembly.
55475A
6.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Engage the 6 claws and the 4 clips and install the No. 2 instrument cluster finish panel garnish.
55604B
7.INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY (for Front Passenger Side)
Engage the 2 claws and install the instrument panel cup holder sub-assembly.
Close the instrument panel cup holder sub-assembly.
55900
8.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
55900A
9.INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
55902C
10.INSTALL AIR CONDITIONING PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
55607
11.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the guide and the 3 claws and install the No. 2 instrument panel under cover sub-assembly.
55550
12.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
With the glove compartment door assembly opened approximately 47° from its closed position, engage the 2 hinges horizontally.
Engaging the hinges from the top will deform the hinges.
Be sure to install the glove compartment door assembly horizontally.
While pushing in the sides of the glove compartment door assembly as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
83100
13.INSTALL COMBINATION METER ASSEMBLY
55410C
14.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Engage the 4 clips and the 2 claws and install the instrument cluster finish panel assembly.
55604A
15.INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY (for Driver Side)
Engage the 2 claws and install the instrument panel cup holder sub-assembly.
55650
16.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 3 claws and the 2 clips and install the No. 1 instrument panel register assembly.
55474C
17.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Engage the 2 claws and the 2 clips and install the No. 1 instrument cluster finish panel garnish.
Close the instrument panel cup holder sub-assembly.
84140
18.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
19.INSTALL UPPER CENTER INSTRUMENT CLUSTER FINISH PANEL
Engage the 3 claws and the clip and install the upper center instrument cluster finish panel.
55411G
20.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
|
Protective Tape |
Engage the 12 clips and the 2 claws and the 4 guides and install the No. 1 instrument cluster finish panel as shown in the illustration.
Remove the protective tape.
55432B
21.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
Connect the connectors.
Engage the 5 clips and the 2 claws and install the lower instrument panel finish panel.
55606
22.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the claw and the guide and install the No. 1 instrument panel under cover sub-assembly.
Install the 3 screws <C>.
23.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
24.INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)
Engage the 2 guides and install the radio tuner opening cover with bracket.
Install the 4 screws.
55412D
25.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL (w/ Radio Receiver)
Connect the connector.
Engage the 7 clips and the 6 claws and install the center instrument cluster finish panel.
55412D
26.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Radio Receiver)
Connect the connector.
Engage the 7 clips and install the center instrument cluster finish panel.
62212
27.INSTALL FRONT PILLAR GARNISH LH
62211
28.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62312B
29.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip LH.
62311B
30.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62112
31.INSTALL COWL SIDE TRIM BOARD LH
62111C
32.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
33.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
34.INSPECT SRS WARNING LIGHT