Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  C1511  Torque Sensor1  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C1511 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1511 Torque Sensor1 Diagnosis Condition: IG ON
Malfunction Status: TRQ1 voltage is less than 0.25 V or more than 4.6 V
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again -

WIRING DIAGRAM

C375646E15
5.844,0.594 6.156,0.792 0.313,0.198 10 false 5V 5.094,0.802 5.708,1 0.615,0.198 10 false TRQV 5.135,1.594 5.75,1.792 0.615,0.198 10 false TRQ1 5.115,2.271 5.729,2.469 0.615,0.198 10 false TRQG 4.875,0.802 5.063,1.031 0.188,0.229 10 false 8 4.885,1.479 5.042,1.677 0.156,0.198 10 false 9 4.885,2.229 5.042,2.427 0.156,0.198 10 false 2 4.854,2.938 5.167,3.135 0.313,0.198 10 false z5 4.854,3.094 7.156,3.375 2.302,0.281 10 false Power Steering ECU Assembly 0.427,3.01 2.865,3.365 2.438,0.354 10 false Torque Sensor (Electric Power Steering Column Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION



PROCEDURE

1.CHECK POWER STEERING ECU ASSEMBLY (TRQ1 VOLTAGE)
a.
C375640C14
0.365,0.969 0.76,1.229 0.396,0.26 1.781,0.896 2.24,0.406 true 1.958,1.479 2.344,1.833 true 1.677,1.49 1.271,1.885 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 0.875,1.833 1.49,2.031 0.615,0.198 10 false TRQV 2.427,1.792 3.042,1.99 0.615,0.198 10 false TRQ1 2.313,0.354 2.927,0.552 0.615,0.198 10 false TRQG 0.51,1.031 0.823,1.229 0.313,0.198 10 false z5
*a Component without harness connected
(Torque Sensor (Electric Power Steering Column Sub-assembly))


Disconnect the power steering ECU assembly connector.


b.

Connect 3 new 1.5 V batteries in series to prepare a 4.5 V power supply.

HINT:

Check that the voltage of the prepared power supply is 4.5 V.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z5-9(TRQ1) - z5-2(TRQG)
1.

Connect the 4.5 V positive (+) terminal to z5-8 (TRQV) and 4.5 V negative (-) terminal to z5-2 (TRQG)

2.

Steering wheel not being turned (without load)


2.07 to 2.43 V
1.

Connect the 4.5 V positive (+) terminal to z5-8 (TRQV) and 4.5 V negative (-) terminal to z5-2 (TRQG)

2.

Steering wheel being turned to right with vehicle stopped


2.25 to 3.42 V
1.

Connect the 4.5 V positive (+) terminal to z5-8 (TRQV) and 4.5 V negative (-) terminal to z5-2 (TRQG)

2.

Steering wheel being turned to left with vehicle stopped


1.08 to 2.25 V


NOTICE:

To avoid damaging the torque sensor (electric power steering column assembly), do not apply a voltage of more than 5 V.


HINT:
·

The voltage values specified above are applicable when using an applied voltage of 4.5 V, and vary depending on the applied voltage (When compared to values for an applied voltage of 5 V, these values differ by a factor of 0.9).

·

When using an applied voltage of 5 V, the specified values are as follows.

Condition Specified Condition
Steering wheel not being turned (without load) 2.3 to 2.7 V
Steering wheel being turned to right with vehicle stopped 2.5 to 3.8 V
Steering wheel being turned to left with vehicle stopped 1.2 to 2.5 V




Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY