Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  C1552  PIG Power Supply Voltage  C1554  Power Supply Relay Failure  


DESCRIPTION

If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1552 PIG Power Supply Voltage PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on After normal confirmation -
C1554 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again -

WIRING DIAGRAM

C280667E01
0.771,0.719 1.656,0.979 0.885,0.26 10 false from Battery 2.625,0.906 3,1.219 0.375,0.313 10 false EPS 4.583,3.198 6.635,3.458 2.052,0.26 10 false Power Steering ECU Assembly 4.594,2.208 5.042,2.448 0.448,0.24 10 false PGND 4.604,0.729 4.979,1.042 0.375,0.313 10 false PIG 4.583,2.99 5.052,3.208 0.469,0.219 10 false F11 4.344,0.573 4.5,0.813 0.156,0.24 10 false 1 4.344,2.01 4.5,2.25 0.156,0.24 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the power steering ECU assembly connectors.

OK:

The power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMT Made)>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (PIG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 142 10

f.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor Min.: 0.0000 V
Max.: 20.1531 V
11 to 14 V Always
OK:

The normal condition value is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
a.
C349134C08
1.469,0.229 1.969,0.479 0.5,0.25 1.083,1.75 1.417,1.25 true 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 1.604,0.271 2.063,0.469 0.458,0.198 10 false F11 0.906,1.802 1.365,2 0.458,0.198 10 false PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F11-1 (PIG) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
C349134C04
1.469,0.229 1.969,0.479 0.5,0.25 2.417,1.667 2.01,1.271 true 0.083,0.083 0.313,0.323 0.229,0.24 10 false *a 1.594,0.271 2.052,0.469 0.458,0.198 10 false F11 2.302,1.698 2.917,1.896 0.615,0.198 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR