Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

C378870E01
0.896,0.635 1.51,0.833 0.615,0.198 10 false CANH 0.906,1.24 1.521,1.438 0.615,0.198 10 false CANL 1.385,0.625 2,0.823 0.615,0.198 10 false F130 1.385,2.646 2,2.844 0.615,0.198 10 false F131 1.104,2.646 1.719,2.844 0.615,0.198 10 false TC 1.385,1.229 2,1.427 0.615,0.198 10 false F130 1.458,1.021 1.771,1.219 0.313,0.198 10 false 14 1.458,2.438 1.771,2.635 0.313,0.198 10 false 19 5.302,1.563 5.917,1.76 0.615,0.198 10 false F12 5.302,1.729 6.594,2.146 1.292,0.417 10 false Power Steering ECU Assembly 5.708,3.594 6.323,3.792 0.615,0.198 10 false F16 5.698,3.771 6.313,3.969 0.615,0.198 10 false DLC3 5.667,0.625 6.281,0.823 0.615,0.198 10 false CANH 5.656,1.219 6.271,1.417 0.615,0.198 10 false CANL 5.667,2.646 6.281,2.844 0.615,0.198 10 false TC 5.656,3.094 6.271,3.292 0.615,0.198 10 false CG 1.458,0.417 1.771,0.615 0.313,0.198 10 false 13 5.427,0.448 5.74,0.646 0.313,0.198 10 false 7 5.427,1.042 5.74,1.24 0.313,0.198 10 false 8 5.375,2.531 5.688,2.729 0.313,0.198 10 false 13 5.438,2.99 5.75,3.188 0.313,0.198 10 false 4 0.823,4.354 2.844,4.625 2.021,0.271 10 false : CAN Communication Line 0.76,3 1.375,3.198 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION


HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C341755C07
1.479,1.021 1.979,1.271 0.5,0.25 1.552,2.094 1.094,3.104 true 2.271,3.073 1.875,2.594 true 0.104,0.177 0.417,0.333 0.313,0.156 10 false *a 1.604,1.052 1.979,1.229 0.375,0.177 10 false F16 0.865,3.031 1.188,3.208 0.323,0.177 10 false CG 2.323,2.99 2.646,3.167 0.323,0.177 10 false TC
*a Front view of DLC3


Turn the ignition switch ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-13 (TC) - F16-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C341755C08
1.479,1.021 1.979,1.271 0.5,0.25 1.552,2.094 1.094,3.104 true 2.271,3.073 1.875,2.594 true 0.104,0.177 0.417,0.333 0.313,0.156 10 false *a 1.604,1.063 1.969,1.24 0.365,0.177 10 false F16 0.865,3.031 1.188,3.208 0.323,0.177 10 false CG 2.323,2.99 2.646,3.167 0.323,0.177 10 false TC
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE POWER STEERING ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Disconnect the F131 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (TC) - F131-19 (TC) Always Below 1 Ω
F16-13 (TC) or F131-19 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C341756C03
1.49,1.031 1.99,1.281 0.5,0.25 1.542,2.115 0.854,3.073 true 0.115,0.156 0.427,0.313 0.313,0.156 10 false *a 1.615,1.073 1.979,1.229 0.365,0.156 10 false F16 0.604,2.99 0.917,3.146 0.313,0.156 10 false CG
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU

6.REPLACE ECM
a.
C341755C09
1.479,1.021 1.979,1.271 0.5,0.25 1.552,2.094 1.094,3.104 true 2.271,3.073 1.875,2.594 true 0.104,0.177 0.417,0.333 0.313,0.156 10 false *a 1.604,1.052 1.958,1.26 0.354,0.208 10 false F16 0.865,3.031 1.188,3.208 0.323,0.177 10 false CG 2.323,2.99 2.646,3.167 0.323,0.177 10 false TC
*a Front view of DLC3


Replace the ECM.



b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE POWER STEERING ECU ASSEMBLY