Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMMIN Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333419 POWER STEERING SYSTEM(for TMMIN Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMMIN Made)  C1511  Torque Sensor Circuit Malfunction  C1512  Torque Sensor Circuit Malfunction  C1513  Torque Sensor Circuit Malfunction  C1514  Torque Sensor Power Supply Abnormal  C1517  Torque Hold Abnormal  


DESCRIPTION

The torque sensor converts the torque input from the steering wheel into electrical signals and sends them to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1511 Torque Sensor Circuit Malfunction A torque sensor (TRQ1) signal error or a loss of the signal.
·

Torque sensor (electric power steering column sub-assembly)


·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.
C1512 Torque Sensor Circuit Malfunction A torque sensor (TRQ2) signal error or a loss of the signal.
·

Torque sensor (electric power steering column sub-assembly)


·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.
C1513 Torque Sensor Circuit Malfunction Deviation between torque sensor TRQ1 and TRQ2 exceeds the specified value.
·

Torque sensor (electric power steering column sub-assembly)


·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.
C1514 Torque Sensor Power Supply Abnormal A torque sensor power source voltage error.
·

Torque sensor (electric power steering column sub-assembly)


·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.
C1517 Torque Hold Abnormal Temporary control due to malfunction related to torque sensor continues for long time.
·

Torque sensor (electric power steering column sub-assembly)

·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.

WIRING DIAGRAM

C293738E04
4.292,0.677 4.5,0.875 0.208,0.198 10 false 1 4.302,1.135 4.51,1.333 0.208,0.198 10 false 2 4.302,1.573 4.51,1.771 0.208,0.198 10 false 8 4.302,2.01 4.51,2.208 0.208,0.198 10 false 9 4.271,0.875 4.479,1.073 0.208,0.198 10 false z5 4.271,1.323 4.479,1.521 0.208,0.198 10 false z5 4.271,1.771 4.479,1.969 0.208,0.198 10 false z5 4.281,2.208 4.49,2.406 0.208,0.198 10 false z5 4.615,0.875 5.115,1.094 0.5,0.219 10 false TRQ2 4.625,1.323 5.125,1.542 0.5,0.219 10 false TRQG 4.625,1.76 5.125,1.979 0.5,0.219 10 false TRQV 4.625,2.208 5.125,2.427 0.5,0.219 10 false TRQ1 4.635,2.635 5.917,3.042 1.281,0.406 10 false Power Steering ECU Assembly 1.469,2.667 3.927,3.031 2.458,0.365 10 false Torque Sensor (Electric Power Steering Column Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMMIN Made)>CALIBRATION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY) - POWER STEERING ECU ASSEMBLY)
a.
C285239C01
0.917,0.229 1.177,0.406 0.26,0.177 0.198,0.188 0.406,0.375 0.208,0.188 10 false *a 0.958,0.229 1.177,0.448 0.219,0.219 10 false z5
*a Component with harness connected
(Power Steering ECU Assembly)


Check the connection condition of the torque sensor (electric power steering column sub-assembly) connector.

OK:

Torque sensor connector (electric power steering column sub-assembly) is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING ECU ASSEMBLY (TORQUE SENSOR OUTPUT)

NG

CONNECT CONNECTOR SECURELY

2.INSPECT POWER STEERING ECU ASSEMBLY (TORQUE SENSOR OUTPUT)
a.

Turn the ignition switch to ON.


b.
C228663C11
0.906,0.802 1.281,1.01 0.375,0.208 1.073,1.646 1.656,2.552 true 1.083,1.823 0.656,2.552 true 1.49,2.573 2.167,2.75 0.677,0.177 10 false TRQG 0.479,2.583 1.135,2.76 0.656,0.177 10 false TRQV 1.031,0.823 1.229,0.99 0.198,0.167 10 false z5 0.177,0.125 0.365,0.292 0.188,0.167 10 false *a
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z5-8 (TRQV) - z5-2 (TRQG) Ignition switch ON 4.5 to 5.5 V


HINT:

When the value is within the specified range, record the value.



Result:
Proceed to
OK
NG



OK

3.INSPECT TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.INSPECT TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)
a.

Turn the ignition switch to ON.


b.
C228663C12
0.906,0.802 1.281,1.01 0.375,0.208 1.073,1.656 1.656,2.563 true 1.021,1.833 0.594,2.563 true 1.958,0.792 1.146,1.656 true 1.5,2.573 2.177,2.75 0.677,0.177 10 false TRQG 1.802,0.563 2.458,0.74 0.656,0.177 10 false TRQ2 1.01,0.802 1.219,0.979 0.208,0.177 10 false z5 0.177,0.125 0.396,0.323 0.219,0.198 10 false *a 0.438,2.573 1.094,2.75 0.656,0.177 10 false TRQ1
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z5-9 (TRQ1) - z5-2 (TRQG) Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 2.5 to 3.8 V
Engine running, steering wheel turned to left with vehicle stopped 1.2 to 2.5 V
z5-1 (TRQ2) - z5-2 (TRQG) Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 1.2 to 2.5 V
Engine running, steering wheel turned to left with vehicle stopped 2.5 to 3.8 V



c.

Calculate the difference between the value recorded when measuring the voltage at terminal TRQV in the previous step, and the sum of the output of torque sensor 1 and torque sensor 2.


OK:

0.3 V or less (Absolute value)


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY)