Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for TMMIN Made) › 2017.10–2018.01
RM30M0E _55 Steering _017104 STEERING COLUMN _0333482 STEERING COLUMN ASSEMBLY(for TMMIN Made) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for TMMIN Made)  REMOVAL  


PROCEDURE

Hide 45130 1.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 2.REMOVE STEERING WHEEL ASSEMBLY

Hide 45289A 3.REMOVE STEERING COLUMN COVER SUPPORT (w/ Smart Entry and Start System)

a.
C284674

Disengage the 4 claws to remove the steering column cover support.


Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

a.
C286512

Remove the 3 screws.


b.

Release the tilt lever.


c.

Disengage the 3 claws to remove the lower steering column cover.


Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

a.
C287884

Disengage the claw to remove the upper steering column cover.


Hide 6.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect all the connectors from the combination switch assembly with spiral cable sub-assembly.


b.
C286513C01
0.375,0.781 0.49,0.646 false 0.385,0.208 0.552,0.396 false 0.24,0.135 0.427,0.281 0.188,0.146 10 false *1 0.24,0.719 0.417,0.885 0.177,0.167 10 true *a
*1 Clamp
*a Claw


Use pliers to hold the clamp and raise the claw with a screwdriver. Remove the combination switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432B 8.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

Hide 45259A 9.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C286514

Fold back the floor carpet.


b.

Remove the 2 clips and column hole cover silencer sheet.


Hide 45209 10.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C286515C01
1.781,1.531 2.156,1.448 2.156,1.448 1.771,1.448 true 2.198,1.354 2.427,1.521 0.229,0.167 10 true *a 1.74,0.635 1.896,0.802 0.156,0.167 10 true A 2.01,1.125 2.167,1.292 0.156,0.167 10 true B
*a Matchmark


Put matchmarks on the steering sliding yoke sub-assembly and steering link assembly.


b.

Loosen bolt A.


c.

Remove bolt B to separate the steering sliding yoke sub-assembly from the steering link assembly.


Hide 55106 11.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY

Hide 12.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect all the connectors and disengage all the wire harness clamps from the steering column assembly.

NOTICE:

Do not pull the wire harness.



b.
C355117

Disconnect the 2 connectors from the power steering ECU assembly.


c.

Disengage the wire harness clamp to separate the wire harness from the instrument panel reinforcement assembly.


d.
C287506

Remove the bolt, 2 nuts and steering column assembly from the instrument panel reinforcement assembly.


Hide 45879A 13.REMOVE BREAK AWAY CAPSULE

a.

Remove the 2 break away capsules from the steering column assembly.