For vehicles equipped with VSC, if a wheel alignment has been performed, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
Perform zero point calibration of the yaw rate and acceleration sensor.
1.INSPECT TIRES
2.MEASURE VEHICLE HEIGHT (for Sedan)
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Front C - A | Rear D - B |
|---|---|
| 87 mm (3.43 in.) | 16 mm (0.630 in.) |
| Front C - A | Rear D - B |
|---|---|
| 67 mm (2.64 in.) | -4 mm (-0.157 in.) |
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear trailing arm bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
3.MEASURE VEHICLE HEIGHT (for Hatchback)
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Front C - A | Rear D - B |
|---|---|
| 87 mm (3.43 in.) | 16 mm (0.63 in.) |
| Front C - A | Rear D - B |
|---|---|
| 67 mm (2.64 in.) | -4 mm (-0.157 in.) |
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear trailing arm bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
Inspect while the vehicle is unloaded.
| *a | Turning Radius Gauge |
| *b | Camber-caster-kingpin Gauge |
Put the front wheel on the center of the turning radius gauge.
Remove the wheel cap or wheel hub ornament.
Install the camber-caster-kingpin gauge at the center of the drive shaft.
Inspect the camber, caster and steering axis inclination.
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | -0°08' +/- 0°45' (-0.13° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | -0°09' +/- 0°45' (-0.15° +/- 0.75°) | |
| 195/50R16 | -0°10' +/- 0°45' (-0.17° +/- 0.75°) |
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 0°09' +/- 0°45' (0.15° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 0°08' +/- 0°45' (0.13° +/- 0.75°) |
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 4°41' +/- 0°45' (4.68° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 4°42' +/- 0°45' (4.70° +/- 0.75°) | |
| 195/50R16 | 4°41' +/- 0°45' (4.68° +/- 0.75°) |
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 4°24' +/- 0°45' (4.40° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 4°25' +/- 0°45' (4.42° +/- 0.75°) |
| Steering Axis Inclination (Reference) |
|---|
| 11°03' (11.05°) |
| Steering Axis Inclination (Reference) |
|---|
| 10°32' (10.53°) |
If the camber, caster and steering axis inclination are not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.
Remove the camber-caster-kingpin gauge.
Install the wheel cap or wheel hub ornament.
5.ADJUST CAMBER
Inspect toe-in after the camber has been adjusted.
Remove the front wheel.
w/ ABS:
Remove the bolt and separate the front flexible hose and front speed sensor wire from the front shock absorber assembly.
Remove the 2 nuts from the lower side of the front shock absorber assembly.
Keep the bolt from rotating while turning the nut.
Clean the installation surfaces of the front shock absorber assembly and steering knuckle.
Temporarily install the 2 nuts. (Step A)
Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)
Tighten the 2 nuts.
Keep the bolts from rotating when tightening the nuts.
w/ ABS:
Install the front flexible hose and front speed sensor wire to the front shock absorber assembly with the bolt.
Install the front flexible hose and front speed sensor wire without twisting them.
Install the front speed sensor harness bracket first and then the front flexible hose bracket.
Install the front wheel.
Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center of the specified range - measured value
Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.
Try to adjust the camber to the center of the specified range.
| To move the axle hub toward (+) in step B | To move the axle hub toward (-) in step B |
|---|---|
| Refer to table (1) (To move the axle hub toward the positive side) | Refer to table (2) (To move the axle hub toward the negative side) |
Table (1) (To move the axle hub toward the positive side)
| *a | Table (1) (To move the axle hub toward the positive side) | *b | Installed Bolt |
| *c | Adjusting Value | *d | 90109-15001 |
| *e | 90109-15002 | *f | 90109-15003 |
| *g | 90109-15004 | *h | Selected Bolt Combination |
Table (2) (To move the axle hub toward the negative side)
| *a | Table (2) (To move the axle hub toward the negative side) | *b | Installed Bolt |
| *c | Adjusting Value | *d | 90109-15001 |
| *e | 90109-15002 | *f | 90109-15003 |
| *g | 90109-15004 | *h | Selected Bolt Combination |
The body and suspension may be damaged if the camber is not correctly adjusted in accordance with the above table.
Replace the nut with a new one when replacing the bolt.
Repeat the steps mentioned above. At step (A), replace 1 or 2 selected bolts.
Replace one bolt at a time when replacing both bolts.
6.INSPECT TOE-IN
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to neutral.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| Tire Size | Specified Condition |
|---|---|
| 175/65R14
185/60R15 |
C + D: 0°09' +/- 0°12' (0.15° +/- 0.20°) |
| B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.) | |
| 195/50R16 | C + D: 0°10' +/- 0°12' (0.16° +/- 0.20°) |
| B - A: 1.6 +/- 2.0 mm (0.0630 +/- 0.0787 in.) |
| Specified Condition |
|---|
| C + D: 0°07' +/- 0°12' (0.12° +/- 0.20°) |
| B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the rack ends.
7.ADJUST TOE-IN
| *a | Thread Length |
Make sure that the thread length of the right and left rack ends are approximately the same.
1.5 mm (0.0591 in.) or less
Remove the steering rack boot clips.
Loosen the tie rod end lock nuts.
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outer-side.
Shorten the longer rack end if the measured toe-in deviates toward the inner-side.
Measure the toe-in.
Turn the right and left rack ends by an equal amount to adjust the toe-in.
Try to adjust the toe-in to the center of the specified range.
Make sure that the thread length of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the steering rack boot clips.
Make sure that the boots are not twisted.
8.INSPECT WHEEL ANGLE
Inspect while the vehicle is unloaded.
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of a turning radius gauge.
Turn the steering wheel fully to the left and right, and measure the turning angle.
| Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|
| 175/65R14 | 38°19' +/- 2°00' (38.32° +/- 2°) | 33°16' (33.27°) |
| 185/60R15 | 38°20' +/- 2°00' (38.33° +/- 2°) | |
| 195/50R16 | 32°54' +/- 2°00' (32.90° +/- 2°) | 29°37' (29.62°) |
| Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|
| 175/65R14 | 38°46' +/- 2°00' (38.77° +/- 2°) | 33°36' (33.60°) |
| 185/60R15 | 38°47' +/- 2°00' (38.78° +/- 2°) |
If the right and left inside wheel angles differ from the specified range, check and adjust the right and left rack end lengths.
9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
10. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION (w/ VSC)