Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for LH Side) › from 2017.10
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090097 FRONT LOWER SUSPENSION ARM(for LH Side) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for LH Side)  INSTALLATION  


PROCEDURE

Hide 48069 1.TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily tighten the front lower No. 1 suspension arm sub-assembly LH with the 2 bolts.


b.

Install the front lower No. 1 suspension arm sub-assembly LH to the front axle assembly with a new castle nut.

NOTICE:

Do not damage the front disc brake dust cover.



c.

Using a 19 mm ball joint lock nut wrench, fully tighten the castle nut.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where a ball joint lock nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the holes for the clip are not aligned, tighten the castle nut by a further turn of up to 60°.

·

Do not allow any oil or grease to contact the threaded or tapered portions of the front lower No. 1 suspension arm sub-assembly LH.

·

Do not damage the front disc brake dust cover.




d.

Install a new clip.


Hide 2.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 3. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 48819A 4.INSTALL FRONT STABILIZER BOLT (w/o Side Rail Reinforcement)

a.
C287060C02
1.573,1.99 1.781,2.146 0.208,0.156 10 true *a 0.438,1.313 0.75,1.469 0.313,0.156 10 false *b 2.854,0.396 3.125,0.552 0.271,0.156 10 false *c 2.896,1.604 3.167,1.76 0.271,0.156 10 false *c
*a Turn
*b Hold
*c Protrusion Length


Install the 4 front stabilizer cushion retainers, front No. 2 stabilizer cushion retainer, 4 front stabilizer cushions and front stabilizer bolt.


b.

While holding the front stabilizer bolt with a wrench, install 2 new nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

Standard Protrusion Length:

2.8 to 4.3 mm (0.110 to 0.169 in.)



Hide 48069 5.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

C277262N01
0.24,0.958 0.396,1.156 0.156,0.198 10 A 2.26,1.917 2.417,2.115 0.156,0.198 10 B

a.

Fully tighten the 2 bolts.

Torque:
Bolt A : 112 N*m (1142 kgf*cm, 83 ft.*lbf)
Bolt B : 165 N*m (1683 kgf*cm, 122 ft.*lbf)


Hide 51405A 6.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 7.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 8.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT