17410
1.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 42 mm (1.65 in.) | 40.5 mm (1.59 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.
Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 8.5 mm (0.335 in.) |
Connect the front exhaust pipe assembly to the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
57533B
2.INSTALL FRONT FLOOR CENTER BRACE (for TMMIN Made)
Install the front floor center brace to the vehicle with the 2 bolts.
57533B
3.INSTALL FRONT FLOOR CENTER BRACE (for TMT Made)
Install the front floor center brace to the vehicle with the 4 bolts.
89465
4.INSTALL HEATED OXYGEN SENSOR
51405A
5.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
51451A
6.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
17430
7.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for TMMIN Made)
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 40 mm (1.57 in.) | 38.5 mm (1.52 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.
Connect the 3 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Tail Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
17430
8.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for TMT Made)
for Sedan:
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 40 mm (1.57 in.) | 38.5 mm (1.52 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.
Connect the 3 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Tail Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
for Hatchback:
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 40 mm (1.57 in.) | 38.5 mm (1.52 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.
Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Tail Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
9.INSPECT FOR EXHAUST GAS LEAK
Perform "Inspection After Repairs" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION