31204
1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY
31230
2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY
31232A
3.REMOVE RELEASE BEARING HUB CLIP
31126
4.REMOVE CLUTCH RELEASE FORK BOOT
31236B
5.REMOVE RELEASE FORK SUPPORT
33823
6.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 3 bolts and No. 1 transmission control cable bracket from the manual transmission case.
33101A
7.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33104
8.REMOVE DRAIN PLUG SUB-ASSEMBLY
Remove the drain plug sub-assembly and gasket from the manual transmission case.
84210
9.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using a 27 mm socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case.
33111G
10.REMOVE MANUAL TRANSMISSION BREATHER PLUG
Using a screwdriver, remove the manual transmission breather plug from the manual transmission case.
33590F
11.REMOVE FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY
| *1 | Floor Shift Selecting Bellcrank Assembly |
| *2 | Control Bellcrank Dust Cover |
Remove the 2 bolts and floor shift selecting bellcrank assembly with control bellcrank dust cover from the manual transmission case.
Remove the control bellcrank dust cover from the floor shift selecting bellcrank assembly.
33544C
12.REMOVE SHIFT LEVER DAMPER
Remove the 2 bolts and shift lever damper from the shift and select lever shaft assembly.
30300
13.SECURE MANUAL TRANSAXLE ASSEMBLY
| *a | Wooden Block |
Place the manual transaxle assembly on wooden blocks.
33295A
14.REMOVE REVERSE RESTRICT SHAFT
Remove the reverse restrict shaft and washer from the manual transmission case.
33266A
15.REMOVE SHIFT INTERLOCK PLATE BOLT (for TMMIN Made)
Remove the shift interlock plate bolt and gasket from the manual transmission case.
33290B
16.REMOVE NO. 2 LOCK BALL ASSEMBLY (for TMT Made)
Remove the No. 2 lock ball assembly from the manual transmission case.
17.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY
Remove the 4 bolts.
Remove the shift and select lever shaft assembly and gasket from the manual transmission case.
33102
18.REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY
Remove the 9 bolts.
|
Projection Part |
Using a plastic hammer, carefully tap the projections of the manual transmission case cover sub-assembly to remove the manual transmission case cover sub-assembly from the manual transmission case.
Do not damage the manual transmission case.
33321G
19.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT
Using SST and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.
Engage the 2 gears simultaneously to lock the transmission.
Using a 27 mm socket wrench, remove the manual transmission output shaft rear set nut.
Disengage the 2 gears.
33214G
20.REMOVE NO. 3 GEAR SHIFT FORK
Remove the No. 3 gear shift fork set bolt from the No. 3 gear shift fork.
Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.
Remove the No. 3 gear shift fork from the No. 3 transmission hub sleeve.
21.INSPECT 5TH GEAR THRUST CLEARANCE
Using a dial indicator, measure the 5th gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.
22.INSPECT 5TH GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 5th gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.
33395
23.REMOVE NO. 3 TRANSMISSION CLUTCH HUB
Using 2 screwdrivers and a hammer, tap out the snap ring.
Use a piece of cloth to keep the snap ring from flying off.
Using a screwdriver, remove the synchromesh shifting key spring from the No. 3 transmission clutch hub.
| *a | Hold |
| *b | Turn |
Using SST, remove the No. 3 transmission clutch hub, 5th gear and No. 3 synchronizer ring from the input shaft.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
Remove the 3 synchromesh shifting keys and synchromesh shifting key spring from the No. 3 transmission clutch hub.
33336A
24.REMOVE 5TH GEAR NEEDLE ROLLER BEARING
| *1 | 5th Gear Needle Roller Bearing |
| *2 | 5th Gear Bearing Spacer |
Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.
33428C
25.REMOVE 5TH DRIVEN GEAR
| *a | Hold |
| *b | Turn |
Using SST, remove the 5th driven gear from the output shaft.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
33151D
26.REMOVE REAR BEARING RETAINER
Remove the 5 bolts and rear bearing retainer from the manual transmission case.
33111R
27.REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING
Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.
33311X
28.REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING
Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.
33451H
29.REMOVE REVERSE IDLER GEAR SHAFT BOLT
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.
33242E
30.REMOVE SHIFT FORK SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 2 gear shift fork shaft.
Use a piece of cloth to keep the shift fork shaft snap ring from flying off.
33275C
31.REMOVE SHIFT DETENT BALL
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a magnet hand, remove the 2 spring seats, 2 compression springs and 2 shift detent balls from the manual transmission case.
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the transaxle case.
Using a magnet hand, remove the spring seat, compression spring and shift detent ball from the transaxle case.
33290
32.REMOVE NO. 1 LOCK BALL ASSEMBLY
Using a 6 mm hexagon socket wrench, remove the No. 1 lock ball assembly from the manual transmission case.
33111
33.REMOVE MANUAL TRANSMISSION CASE
Remove the 3 bolts from the transaxle case.
| *1 | Clutch Tube Bracket |
Remove the 13 bolts and clutch tube bracket from the manual transmission case.
Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the manual transmission case from the transaxle case.
Do not damage the manual transmission case and transaxle case.
33402
34.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
| *1 | Reverse Idler Gear Sub-assembly |
| *2 | Reverse Idler Gear Thrust Washer |
| *3 | Reverse Idler Gear Shaft |
Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the transaxle case.
33240
35.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY
Remove the 2 bolts and reverse shift arm bracket assembly from the transaxle case.
33243A
36.REMOVE NO. 2 GEAR SHIFT FORK SHAFT
Remove the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt from the No. 2 gear shift fork and No. 1 gear shift head.
| *1 | No. 1 Gear Shift Head |
| *2 | No. 2 Gear Shift Fork Shaft |
Remove the No. 2 gear shift fork shaft and No. 1 gear shift head from the transaxle case.
33212A
37.REMOVE NO. 1 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring.
Use a piece of cloth to keep the shift fork shaft snap ring from flying off.
| *1 | No. 1 Gear Shift Fork Shaft |
Remove the No. 1 gear shift fork set bolt and No. 1 gear shift fork shaft from the No. 1 gear shift fork.
Remove the No. 1 gear shift fork.
33244G
38.REMOVE NO. 3 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.
Use a piece of cloth to keep the shift fork shaft snap ring from flying off.
| *1 | No. 3 Gear Shift Fork Shaft |
| *2 | No. 2 Gear Shift Fork |
| *3 | Reverse Shift Fork |
Remove the No. 3 gear shift fork shaft together with the reverse shift fork and No. 2 gear shift fork from the transaxle case.
Using a magnet hand, remove the 2 reverse shift fork balls from the reverse shift fork.
Secure the No. 3 gear shift fork shaft in a vise between aluminum plates.
Do not overtighten the vise.
Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.
Use a piece of cloth to keep the shift fork shaft snap ring from flying off.
Remove the reverse shift fork from the No. 3 gear shift fork shaft.
39.REMOVE INPUT SHAFT ASSEMBLY
Remove the input shaft assembly and output shaft assembly from the transaxle case.
40.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case assembly from the transaxle case.
33125
41.REMOVE MANUAL TRANSAXLE CASE RECEIVER
Remove the bolt and manual transaxle case receiver from the transaxle case.
33280
42.REMOVE REVERSE RESTRICT PIN ASSEMBLY
Using a 6 mm hexagon socket wrench, remove the reverse restrict pin plug from the manual transmission case.
Using a 5 mm pin punch and a hammer, drive out the reverse restrict pin slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.
33124C
43.REMOVE NO. 1 OIL RECEIVER PIPE
Remove the bolt and No. 1 oil receiver pipe from the manual transmission case.
Do not damage the No. 1 oil receiver pipe.
33124D
44.REMOVE NO. 2 OIL RECEIVER PIPE
Remove the bolt and No. 2 oil receiver pipe from the manual transmission case.
Do not damage the No. 2 oil receiver pipe.
33326
45.REMOVE BEARING LOCK PLATE
Remove the bolt and bearing lock plate from the transaxle case.
33449
46.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the transaxle case.
33311A
47.REMOVE INPUT SHAFT FRONT BEARING
| *a | Hold |
| *b | Turn |
Using SST, remove the input shaft front bearing from the transaxle case.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
31105D
48.REMOVE FRONT TRANSAXLE CASE OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the front transaxle case oil seal from the transaxle case.
Make sure not to damage the inside of the transaxle case.
33321N
49.REMOVE OUTPUT SHAFT FRONT BEARING
Using SST, remove the output shaft front bearing from the transaxle case.
Do not apply excessive force to the transaxle case when using SST.
33134B
50.REMOVE OUTPUT SHAFT COVER
Remove the output shaft cover from the transaxle case.
41311E
51.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
| *a | Hold |
| *b | Turn |
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential case front plate washer from the transaxle case.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
| *a | Hold |
| *b | Turn |
Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
43410M
52.REMOVE FRONT DRIVE SHAFT OIL SEAL RH
Using SST and a hammer, drive out the front drive shaft oil seal RH from the transaxle case.
41311F
53.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
| *a | Hold |
| *b | Turn |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear plate washer from the manual transmission case.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
| *a | Hold |
| *b | Turn |
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
43420H
54.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, drive out the front drive shaft oil seal LH from the manual transmission case.