Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE FLUID › from 2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0259987 CONTINUOUSLY VARIABLE TRANSAXLE FLUID A

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.

Remove the engine under cover LH (w/o Metal type under cover).

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


c.

Remove the center engine under cover (w/ Metal type under cover).

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


d.

Remove the No. 1 engine under cover sub-assembly (w/ Metal type under cover).

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL


e.
C264233

Remove the refill plug and gasket from the rear transaxle case. [#2]


f.
C264234

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly and drain the fluid. [#3]


g.
C264235C08
2.438,0.323 2.667,0.563 true 2.292,0.25 2.563,0.448 0.271,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly and drain the fluid. [#4]


h.
C235873

Measure the amount of fluid drained. [#5]

HINT:

Add the same amount of fluid in step [#8].



i.
C264235C08
2.438,0.323 2.667,0.563 true 2.292,0.25 2.563,0.448 0.271,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil (CVT) pan sub-assembly. [#6]

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


j.
C264234

Using a 6 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle oil (CVT) pan sub-assembly. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



k.
C300996

Add fluid to the refill hole using the same amount of fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine CVT fluid FE.



l.
C264233

Temporarily install the refill plug and gasket to the rear transaxle case. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



m.

Lower the vehicle. [#10]


n.

Start the engine. [#11]


o.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds). [#12]

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle assembly.



p.

Allow the engine assembly to idle for 30 seconds to warm it up. [#13]


q.

Turn the ignition switch off. [#14]


r.

Repeat steps [#1] to [#14].


s.

Repeat steps [#1] to [#10].


Hide 3.ADJUST FLUID TEMPERATURE (when Using the GTS)

Hide 4.ADJUST FLUID TEMPERATURE (when Not Using the GTS)

Hide 6.PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If approximately 50% or more of the CVT fluid has been replaced during a repair of the transaxle or a similar operation, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION