Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for CVT) › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262366 ENGINE ASSEMBLY(for CVT) A

2NR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for CVT)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE FRONT WHEELS

Hide 51442C 5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51441C 6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 11.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 23826 13.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A384949

Slide the hose clip and disconnect the No. 1 fuel vapor feed hose from the purge VSV (purge valve).


Hide 23827A 14.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A384950

Disconnect the No. 2 fuel vapor feed hose from the purge VSV (purge valve).


Hide 17341T 15.DISCONNECT NO. 1 AIR HOSE

Hide 12262 16.DISCONNECT NO. 2 VENTILATION HOSE

Hide 17880 17.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 18.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A381362

Disconnect the mass air flow meter connector.


b.

Disengage the 2 clamps to separate the engine wire from the air cleaner cap sub-assembly.


c.

Disengage the 2 clamps of the air cleaner cap sub-assembly.


d.

Disengage the 2 guides to remove the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


Hide 17801 19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.
A381365

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A381268

Disengage the clamp to separate the engine wire from the air cleaner case sub-assembly.


b.

Remove the 3 bolts and air cleaner case sub-assembly from the air cleaner bracket.


Hide 28800 21.REMOVE BATTERY

a.

Remove the terminal cover from the positive (+) battery terminal.


b.
A313887C03
0.365,0.135 0.5,0.26 true 0.698,0.458 0.823,0.188 true 0.198,0.063 0.51,0.219 0.313,0.156 10 false *1 0.854,0.083 1.167,0.24 0.313,0.156 10 false *2
*1 Engine Room Main Wire
*2 Engine Wire


Remove the nut to disconnect the engine room main wire with engine wire from the positive (+) battery terminal.


c.

Disengage the 2 claws to disconnect the engine room main wire from the engine wire.


d.

Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.


e.

Remove the battery from the battery tray.


Hide 74431 22.REMOVE BATTERY TRAY

a.
A111180

Remove the battery tray from the battery carrier assembly.


Hide 74410 23.REMOVE BATTERY CARRIER ASSEMBLY

A382169

a.

Disengage the 4 clamps to disconnect the wire harness from the battery carrier assembly.


b.

Remove the 5 bolts and battery carrier assembly from the engine mounting insulator LH and vehicle.


Hide 16361A 24.REMOVE FAN AND GENERATOR V BELT

Hide 15301 25.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 11452 26.REMOVE OIL LEVEL DIPSTICK GUIDE

Hide 17167 27.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 82121 28.DISCONNECT ENGINE WIRE

Hide 29.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 27020 30.REMOVE GENERATOR WITH REGULATOR ASSEMBLY

Hide 44774 31.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A382561

Slide the hose clip and disconnect the union to connector tube hose from the intake manifold.


Hide 25860D 32.SEPARATE VACUUM SWITCHING VALVE ASSEMBLY

a.
A382171

Disconnect the vacuum switching valve assembly connector.


b.

Remove the bolt and separate the vacuum switching valve assembly from the intake manifold.


Hide 17341T 33.DISCONNECT NO. 1 AIR HOSE

a.
A382170

Disengage the clamp to disconnect the No. 1 air hose from the intake manifold.


Hide 16571C 34.DISCONNECT NO. 1 RADIATOR HOSE

a.
A382563

Slide the hose clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


Hide 16572D 35.DISCONNECT NO. 2 RADIATOR HOSE

a.
A381363

Slide the hose clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87246 36.DISCONNECT OUTLET HEATER WATER HOSE

a.
A382532

Slide the hose clip and disconnect the outlet heater water hose from the heater radiator assembly.


Hide 87245 37.DISCONNECT INLET HEATER WATER HOSE

A382533

a.

Slide the hose clip and disconnect the inlet heater water hose from the heater radiator assembly.


Hide 23841B 38.REMOVE EFI FUEL PIPE CLAMP

Hide 23901 39.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 88320 40.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Cooler System)

a.
A381266

Disconnect the cooler compressor assembly connector.


b.

Remove the 4 bolts and separate the cooler compressor assembly from the cylinder block sub-assembly and oil pan sub-assembly.

NOTICE:

Separate the cooler compressor assembly together with the discharge hose and suction hose, then suspend them from the vehicle with a piece of rope.



Hide 55550 41.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 42.DISCONNECT ENGINE WIRE (for LHD)

a.

Remove the relay block cover from the engine room relay block.


b.
A304783

Remove the bolt to disconnect the engine wire from the vehicle.


c.

Disengage the clamp to disconnect the engine wire from the vehicle.


d.

Disconnect the connector from the engine room relay block.


e.

Remove the nut from the engine room relay block.


f.

Disengage the 2 claws to disconnect the engine wire from the engine room relay block.


g.
A382534

Disconnect the 4 connectors.


h.

Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.


i.
A313899

Disengage the clamp to disconnect the engine wire from the wire harness clamp bracket.


j.

Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.


Hide 82121 43.DISCONNECT ENGINE WIRE (for RHD)

a.

Remove the relay block cover from the engine room relay block.


b.
A304783

Remove the bolt to disconnect the engine wire from the vehicle.


c.

Disengage the clamp to disconnect the engine wire from the vehicle.


d.

Disconnect the connector from the engine room relay block.


e.

Remove the nut from the engine room relay block.


f.

Disengage the 2 claws to disconnect the engine wire from the engine room relay block.


g.
A381360

Disconnect the 3 connectors.


h.

Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.


i.
A112922

Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.


Hide 57533B 44.REMOVE FRONT FLOOR CENTER BRACE (for TMT Made)

Hide 57533B 45.REMOVE FRONT FLOOR CENTER BRACE (for TMMIN Made)

Hide 17410 46.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 47.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 45259A 49.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 50.DISCONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 51.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 43498A 52.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR

a.
A381267

Remove the 2 bolts and No. 1 drive shaft heat insulator from the oil pan sub-assembly.


Hide 12137 53.REMOVE OIL PAN PROTECTOR (w/ Metal Type Under Cover)

a.
A380370

Remove the 3 bolts and oil pan protector from the oil pan sub-assembly.


Hide 12144 54.REMOVE OIL PAN COVER SILENCER (w/ Metal Type Under Cover)

HINT:

Perform this procedure only when replacement of the oil pan cover silencer is necessary.


a.
A380371

Remove the oil pan cover silencer from the oil pan protector.


Hide 55.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A381357

Remove the bolt and wire harness clamp bracket from the continuously variable transaxle assembly.


Hide 56.REMOVE ENGINE ASSEMBLY WITH CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
A384951

Loosen the engine moving control rod bolt.


b.
A382176C01
0,0 0,0 false
V100155

Attachment Placement Positions


Place the height adjustment or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with continuously variable transaxle assembly and front suspension crossmember sub-assembly.

NOTICE:
·

Place the height adjustment and plate lift attachments so that the engine assembly with continuously variable transaxle assembly is level.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

As the engine assembly with continuously variable transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the continuously variable transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the continuously variable transaxle assembly.




c.
A245921

Remove the bolt and 2 nuts to disconnect the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
C354275

Remove the through bolt and nut to disconnect the engine mounting insulator LH from the engine mounting bracket LH.

HINT:

Loosen by holding the nut and turning the bolt.



e.
A382529

Remove the 6 bolts and engine assembly with continuously variable transaxle assembly with front suspension crossmember sub-assembly from the vehicle.

NOTICE:

When removing the engine assembly with continuously variable transaxle assembly and front suspension crossmember sub-assembly, be careful not to damage any wire harnesses or the steering shaft.



Hide 28100 57.REMOVE STARTER ASSEMBLY

Hide 11363A 58.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 32101G 59.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 60.INSTALL ENGINE HANGER

a.
A381269C01
1.281,0.26 1.99,0.854 true 1.302,2.479 1.688,2.833 true 1.115,0.177 1.427,0.375 0.313,0.198 10 false *1 1.135,2.396 1.448,2.594 0.313,0.198 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger to the cylinder head sub-assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Part Name Part No.
No. 1 engine hanger 12281-0Y070
No. 2 engine hanger 12282-0Y060
Bolt 90105-T0125



Hide 51201 61.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A382538

a.

Using an engine sling device and a chain block, suspend the engine assembly with continuously variable transaxle assembly.


b.

Remove the through bolt and front suspension crossmember from the No. 2 engine moving control rod.


Hide 82121 62.REMOVE ENGINE WIRE

a.
A203892

Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.


b.
A381359

Remove the 2 nuts to disconnect the engine wire from the cylinder head cover sub-assembly.


c.
A381361

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


d.

Disconnect all the engine wire connectors.

NOTICE:

Make sure that no engine wires are connected to the engine.



Hide 16260 63.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
A382536

Slide the hose clip and disconnect the water by-pass hose assembly from the No. 1 water by-pass pipe sub-assembly.


Hide 87245 64.REMOVE INLET HEATER WATER HOSE

a.
A382535

Disengage the clamp to disconnect the hose clamp from the wire harness clamp bracket.


b.

Slide the hose clip to separate the inlet heater water hose from the cylinder head sub-assembly.


Hide 65.FIX ENGINE ASSEMBLY

a.

Attach the sling device to the engine hangers and chain block.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.
A382531C01
0,0 0,0 false
V100155

Attachment Placement Position


To enable removal of the continuously variable transaxle assembly, adjust the positions of the height adjustment and plate lift attachments and set them in place.

NOTICE:
·

Place the height adjustment and plate lift attachments so that the engine assembly with continuously variable transaxle assembly is level.

·

As the engine assembly with continuously variable transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the continuously variable transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the continuously variable transaxle assembly.




c.
A305264

Use a belt with a tightening mechanism or a rope to secure the engine assembly to the engine lifter.

NOTICE:

Do not tighten the belt with a tightening mechanism or the rope any more than is necessary.



Hide 30400 66.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Hide 32101B 67.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustable attachments and plate lift attachments, place the engine assembly horizontally.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A305670E01
2.146,1.99 2.385,1.75 true 2.458,1.677 2.844,1.844 0.385,0.167 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A382920

Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly and the front drive plate spacer from the crankshaft.


Hide 68.INSTALL ENGINE STAND

a.

Using a sling device and chain block, install the engine assembly to the engine stand.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




Hide 12305 69.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A382174

Remove the 3 bolts.


b.

Disengage the hook and remove the engine mounting insulator sub-assembly RH from the vehicle.


Hide 12372A 70.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A383014

Remove the 5 bolts.


b.

Disengage the hook and remove the engine mounting insulator LH from the vehicle.