Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is cancelled when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C353731C01
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 2.583,2.333 2.177,1.594 true 2.583,4.5 2.177,3.771 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 2.667,4.417 3.125,4.615 0.458,0.198 10 false IG1 2.667,2.25 3.125,2.448 0.458,0.198 10 false IG1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A35-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A47-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



e.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC (C1417) is not output A
DTC (C1417) is output B



A

B