| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1427 | Motor Malfunction | Actuator pump motor does not operate properly. | ·
Brake actuator assembly (Ground circuit) ·
Brake actuator assembly (Motor circuit) |
Refer to DTCs C146C and C146D.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C146C
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Motor Relay | ABS motor relay | Relay OFF / ON | Operating sound of motor can be heard.
[Vehicle condition] Vehicle stopped |
| Tester Display |
|---|
| Motor Relay |
Check for operating sound of the ABS motor relay when operating it with the GTS.
| Result | Proceed to |
|---|---|
| The operating sound is not heard | A |
| The operating sound is heard | B |
A
B
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Check the connector case and terminals for deformation and corrosion.
No deformation or corrosion.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-24 (+BM) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-24 (+BM) - Body ground | Always | 11 to 14 V |
Turn the ignition switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-13 (GND2) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-13 (GND2) - Body ground | Always | Below 1 Ω |
Reconnect the skid control ECU (brake actuator assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
This code is detected when a problem is identified in the skid control ECU (brake actuator assembly).
The ABS motor relay is in the skid control ECU (brake actuator assembly).
Therefore, ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC (C1427) is not output | A |
| DTC (C1427) is output | B |
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
The DTCs were probably output due to a bad connection of the connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B