The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the brake actuator assembly.
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation is not possible.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NR-FE) | B |
| NG (for 2NR-FE) | C |
A
B
C
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A35-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A47-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | except LHD with Continuously Variable Transaxle |
| *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-1 (GND1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-1 (GND1) - Body ground | Always | Below 1 Ω |
Reconnect the skid control ECU (brake actuator assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Parking Brake SW | Parking brake switch | OFF or ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Tester Display |
|---|
| Parking Brake SW |
Using the GTS, check that the switch condition displayed on the GTS changes according to the parking brake operation.
When the parking brake is operated, the display changes as shown above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly)) |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the A22 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the brake fluid level.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
If the switch condition is normal, adjust the brake fluid level to the MAX level.
Reinstall the reservoir filler cap and strainer.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-28 (SW) - A22-1 (+) | Always | Below 1 Ω |
| F38-28 (SW) or A22-1 (+) - Body ground | Always | 10 kΩ or higher |
| A22-2 (E) - Body ground | Always | Below 1 Ω |
Reconnect the F38 combination meter assembly connector.
Reconnect the A22 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake warning light | OFF or ON | OFF: Warning light off
ON: Warning light on |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the ABS warning light.
| Result | Proceed to |
|---|---|
| Display of the Data List remains OFF | A |
| Display of the Data List remains ON | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
A
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Component without harness connected
(Parking Brake Switch Assembly) |
Turn the ignition switch off.
Disconnect the F14 parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Switch on
(Switch pin free) |
Below 1 Ω |
| 1 - Body ground | Switch off
(Switch pin pushed in) |
10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-16 (PKBI) - F14-1 | Always | Below 1 Ω |
| F38-16 (PKBI) or F14-1 - Body ground | Always | 10 kΩ or higher |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG