Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1427  Motor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1427 Motor Malfunction Actuator pump motor does not operate properly.
·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


e.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay Motor relay Relay ON / OFF Operating sound of motor can be heard.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2
f.

Check the operating sound of the motor relay when operating it with the GTS.


Result:
Result Proceed to
The operating sound is not heard (for TMMIN Made) A
The operating sound is not heard (for TMT Made) B
The operating sound is heard C



A

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

B

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

C

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.
C349101C04
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,2.125 1.042,1.583 true 0.5,4.125 1.042,3.583 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,2.042 0.479,2.281 0.396,0.24 10 false GND2 0.083,4.042 0.479,4.281 0.396,0.24 10 false GND2
*A for Manual Transaxle
*B for Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle
Tester Connection Condition Specified Condition
A48-13 (GND2) - Body ground Always Below 1 Ω

for Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: for Manual Transaxle

*2: for Continuously Variable Transaxle




Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.



Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.
C349101C36
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,2.125 1.042,1.583 true 0.5,4.125 1.042,3.583 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,2.042 0.479,2.281 0.396,0.24 10 false GND2 0.083,4.042 0.479,4.281 0.396,0.24 10 false GND2
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A48-13 (GND2) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

5.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle




Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.



Result:
Result Proceed to
DTC is not output A
DTC is output B



A

B