Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1428  Motor Circuit Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1428 Motor Circuit Malfunction With the ABS motor relay OFF and the ABS motor fail safe relay ON, an open in the motor circuit continues for 2 seconds or more. Brake actuator assembly (Motor circuit)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CONFIRM MODEL
Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

B

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.
C349101C04
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,2.125 1.042,1.583 true 0.5,4.125 1.042,3.583 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,2.042 0.479,2.281 0.396,0.24 10 false GND2 0.083,4.042 0.479,4.281 0.396,0.24 10 false GND2
*A for Manual Transaxle
*B for Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle
Tester Connection Condition Specified Condition
A48-13 (GND2) - Body ground Always Below 1 Ω

for Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.
C349101C36
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,2.125 1.042,1.583 true 0.5,4.125 1.042,3.583 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.083,2.042 0.479,2.281 0.396,0.24 10 false GND2 0.083,4.042 0.479,4.281 0.396,0.24 10 false GND2
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A48-13 (GND2) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A49-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)