The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1432 | Steering Angle Sensor Power Source Voltage Malfunction | Steering angle sensor power supply malfunction signal is received from steering angle sensor. | ·
DOME fuse ·
IG1 NO. 2 fuse ·
Steering angle sensor (Spiral cable sub-assembly)*1 ·
Steering angle sensor*2 ·
Wire harness or connector |
*1: for TMMIN Made
*2: for TMT Made
for TMMIN Made
for TMT Made
Do not remove the steering angle sensor from the spiral cable sub-assembly*1.
When replacing the steering angle sensor (spiral cable sub-assembly), confirm that the replacement part is of the correct specification*1.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
*1: for TMMIN Made
When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
When the speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly) has trouble, DTCs for the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2 may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2.
*1: for TMMIN Made
*2: for TMT Made
| Result | Proceed to |
|---|---|
| for TMMIN Made | A |
| for TMT Made | B |
A
B
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the steering angle sensor (spiral cable sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F116-6 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F116-5 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F116-2 (ESS) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the steering angle sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F147-5 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F147-4 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F147-1 (ESS) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG