Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C349107E02
0.688,3.583 1.146,3.781 0.458,0.198 10 false ECM 0.688,3.417 1.146,3.615 0.458,0.198 10 false F131 1.167,2.427 1.625,2.625 0.458,0.198 10 false TC 1.5,2.313 1.958,2.51 0.458,0.198 10 false 19 5.5,2.313 5.958,2.51 0.458,0.198 10 false 13 5.573,2.854 6.031,3.052 0.458,0.198 10 false 4 5.813,2.427 7.135,2.677 1.323,0.25 10 false TC 5.833,2.948 7.156,3.198 1.323,0.25 10 false CG 6.063,3.323 6.521,3.521 0.458,0.198 10 false F16 6.063,3.49 6.521,3.688 0.458,0.198 10 false DLC3 5.479,1.552 7.052,1.99 1.573,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 0.823,4.281 3.76,4.563 2.938,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C280109C58
1.542,0.146 1.917,0.417 0.375,0.271 1.604,0.813 1.177,0.396 true 1.844,1.5 1.438,1.865 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 0.938,0.302 1.25,0.5 0.313,0.198 10 false CG 1.229,1.802 1.5,2 0.271,0.198 10 false TC 1.615,0.208 1.906,0.365 0.292,0.156 10 false F16
*1 DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-13 (TC) -F16-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
NG
OK



NG

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

OK

INSPECT ECM (TC of DLC3 INPUT)

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the F131 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (TC) - F131-19 (TC) Always Below 1 Ω
F16-13 (TC) or F131-19 (TC) - Body ground Always 10 kΩ or higher



d.

Reconnect the F131 ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) -Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C280109C59
1.542,0.146 1.917,0.417 0.375,0.271 1.604,0.813 1.177,0.396 true 1.844,1.5 1.438,1.865 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 0.938,0.302 1.25,0.5 0.313,0.198 10 false CG 1.229,1.802 1.5,2 0.271,0.198 10 false TC 1.615,0.208 1.906,0.365 0.292,0.156 10 false F16
*1 DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Result Proceed to
MIL is blinking A
MIL is not blinking (for 1NR-FE) B
MIL is not blinking (for 2NR-FE) C



A

B

C