Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan) › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334263 CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 62170A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

NOTICE:

When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Engage the 5 clips (B) to temporarily install the curtain shield airbag assembly.

B484602C01
3.083,2.021 3.313,2.271 true 2.583,2.167 2.323,2.438 2.323,2.438 2.948,2.188 true 2.99,1.635 3.25,1.635 false 5.229,2.073 5.49,2.073 true 0.323,1.323 0.385,0.729 0.385,0.729 1.042,0.927 true 3.292,2.292 3.604,2.448 0.313,0.156 10 false *1 3.26,1.531 3.573,1.688 0.313,0.156 10 false *a 2.458,0.625 2.688,0.813 0.229,0.188 10 true *b 5.531,1.969 5.844,2.125 0.313,0.156 10 false *c 2.125,2.333 2.438,2.49 0.313,0.156 10 false *d 0.208,0.625 0.521,0.781 0.313,0.156 10 false *e 4.667,0.677 4.896,0.865 0.229,0.188 10 true *b 5.198,0.719 5.427,0.906 0.229,0.188 10 true *b 6.531,1.052 6.76,1.24 0.229,0.188 10 true *b 3.646,0.479 3.875,0.667 0.229,0.188 10 true *b
*1 Spacer - -
*a Clip (A) *b Clip (B)
*c Pin *d Claw
*e Spacer Location - -



d.

Install the 3 new bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.



e.

Install the curtain shield airbag assembly with 2 new spacers and 6 new clips (A).

HINT:

Engage the 12 claws to install the 6 clips (A).



f.

Using needle nose pliers, push the 6 pins into the 6 clips (A).

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the clips are pushed in firmly.




g.
B484604C01
2.677,0.792 2.958,0.635 true 1.281,2.74 1.656,2.229 true 1.104,2.635 1.417,2.792 0.313,0.156 10 false *a 2.969,0.521 3.198,0.698 0.229,0.177 10 false *b
*a Airbag Connector
*b Airbag Connector Lock


Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



h.

Push in the airbag connector lock to install the airbag connector.

NOTICE:

Securely lock the airbag connector lock.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)