Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan) › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334263 CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan) N

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be accidentally deployed by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a curtain shield airbag assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors where it will not disturb nearby residents.

·

When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the curtain shield airbag assembly.

·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 62170A 2.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed to Vehicle)

NOTICE:
·

When disposing of a curtain shield airbag assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to perform the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




e.

Disconnect the curtain shield airbag assembly connector.

i.
B484598C01
1.885,2.271 2.396,1.729 true 1.219,2.729 1.646,2.302 true 0.958,0.781 1.24,0.573 true 1.135,2.708 1.344,2.875 0.208,0.167 10 false *a 1.26,0.458 1.573,0.615 0.313,0.156 10 false *b 2.417,1.594 2.656,1.771 0.24,0.177 10 false *c
*a Airbag Connector
*b Airbag Connector Lock
*c Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

i.
B484606N01
2.417,1.188 2.771,1.188 false 1.667,1.615 1.667,1.948 1.667,1.948 2.333,1.948 false 2.167,1.615 2.167,1.948 false 2.833,1.104 3.292,1.302 0.458,0.198 10 false SST 2.385,1.854 2.844,2.052 0.458,0.198 10 false SST

After connecting the following SST to each other, connect them to the curtain shield airbag assembly.

SST
09082-00700  
09082-00802  (09082-10801, 09082-20801)

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
C202800C05
1.583,0.458 1.802,0.24 1.802,0.24 1.896,0.24 false 0.771,1.385 0.615,1.229 0.615,1.229 0.417,1.229 false 1.615,1.792 1.844,2.021 0.229,0.229 10 false *b 0.125,1.156 0.49,1.406 0.365,0.25 10 false SST 1.958,0.167 2.198,0.417 0.24,0.25 10 false *a
*a Battery
*b 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the rear side window of the vehicle.


iii.

Maintaining sufficient clearance for the SST wire harness in the rear side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is inside or near the vehicle.

·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 62170A 3.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed to Vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  


b.

Remove the curtain shield airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY(for Sedan)>REMOVAL

CAUTION:
·

Before removing the curtain shield airbag assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.




c.
B484608

Cut off the deployment section of the curtain shield airbag assembly.


d.
B104882C16
2.313,0.938 2.052,0.427 2.052,0.427 1.875,0.427 false 2.656,1.469 2.896,1.646 0.24,0.177 10 *a 1.635,0.333 1.844,0.521 0.208,0.188 10 *b
*a Wire Diameter
*b Stripped Wire Cross Sectional Area


Using braided wire, tie down the curtain shield airbag assembly to an unneeded tire.

Wire:

Stripped wire cross sectional area

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the curtain shield airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross sectional area of the stripped wire:

Cross sectional area = 3.14 x (Diameter)2 / 4


i.
B279805C03
1.458,0.26 1.698,0.51 0.24,0.25 10 *a 0.958,1.49 1.188,1.771 0.229,0.281 10 *b
*a Width
*b Inner Diameter


Position the curtain shield airbag assembly inside the tire as shown in the illustration.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:

Make sure that the wires are tight. If there is slack in the wires, the curtain shield airbag assembly may break loose when the airbag is deployed.


NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




e.

Install SST.

i.
B345257N01
1.823,1.656 1.823,1.406 1.823,1.406 0.885,1.406 false 1.156,1.406 1.156,1.948 false 0.563,1.333 1.021,1.531 0.458,0.198 10 false SST

After connecting the following SST to each other, connect them to the curtain shield airbag assembly.

SST
09082-00802  (09082-10801, 09082-20801)



f.

Place the tires.

CAUTION:

Do not face the deployment side of the curtain shield airbag assembly toward the ground.


i.
B289033C04
2.406,1.5 2.594,1.76 0.188,0.26 10 false *a 2.406,0.708 2.625,0.938 0.219,0.229 10 false *a 1.594,0.042 1.813,0.26 0.219,0.219 10 false *b 0.719,0.854 0.948,1.115 0.229,0.26 10 false *c
*a Tires (2 or more)
*b Inner Diameter
*c Width


Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


NOTICE:

Do not place the SST connector under the tire because it could be damaged.



ii.

Place at least 2 tires onto the tire to which the curtain shield airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:

The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.



iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




g.

Install SST.

i.
B279808C04
1.51,1.844 1.51,2.063 false 0.375,2.688 0.375,2.927 false 2.365,1.323 1.573,0.531 1.573,0.531 1.396,0.531 true 1.229,0.458 1.479,0.646 0.25,0.188 10 false *1 1.26,2.76 1.5,2.917 0.24,0.156 10 false *b 0.25,2.958 0.583,3.156 0.333,0.198 10 false SST 1.448,2.083 1.677,2.24 0.229,0.156 10 false *a
*1 Curtain Shield Airbag Assembly
*a Battery
*b 10 m (32.8 ft.) or more


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



h.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the curtain shield airbag assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




i.

Dispose of the curtain shield airbag assembly.

CAUTION:
·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the curtain shield airbag assembly from the tire.


ii.

Place the curtain shield airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.