Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334272 FRONT SEAT SIDE AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a front seat side airbag assembly that has an undeployed airbag.

·

The airbag emits an exploding sound when it is deployed, so perform the operation outdoors, and where it will not create a nuisance to nearby residents.

·
B104819E08
2.406,0.385 2.292,0.729 false 2.083,0.729 2.417,0.927 0.333,0.198 10 false SST

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the front seat side airbag assembly.

·

The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a front seat side airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



PROCEDURE

Hide 73910A 1.DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the front seat side airbag assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E06
0.145,0.656 0.521,0.857 0.376,0.201 10 SST 0.964,1.227 0.735,0.775 false 0.735,0.775 0.548,0.775 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820C17
1.917,1.313 1.979,1.677 false 2.51,0.802 2.719,0.802 false 1.865,1.677 2.198,1.875 0.333,0.198 10 false SST 2.781,0.719 3.115,0.917 0.333,0.198 10 false *1
*1 Battery


Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

SST
09082-00700  


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the front seat side airbag assembly under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push the slider with a finger to disengage the first claw. Without releasing your finger, slide the slider to disengage the second claw and disconnect the front seat side airbag connector.

B273982C24
1.649,1.316 1.017,0.857 false 0.856,0.778 1.057,0.93 0.201,0.153 10 *a 3.479,1.296 2.847,0.837 false 2.686,0.758 2.887,0.91 0.201,0.153 10 *b 3.546,1.295 4.151,1.052 false 4.166,0.972 4.332,1.127 0.166,0.155 10 *1
*1 Slider - -
*a Push *b Slide




d.

Connect SST.

CAUTION:

Check that there is no looseness in the front seat assembly.


i.
B286403C02
0.42,0.603 0.74,0.341 false 0.755,0.224 1.041,0.436 0.286,0.212 10 *1 1.395,2.978 1.705,3.124 0.311,0.146 10 SST 1.148,3.057 1.392,3.057 false
*1 Slider


Connect the SST connector to the front seat side airbag assembly connector.

SST
09082-00700  
09082-00820  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
U134482C06
1.01,1.854 2.49,1.854 false 2.625,1.042 2.625,1.917 false 0.875,1.792 0.875,1.917 false 0.406,1.25 0.635,1.542 false 1.74,0.854 2.208,0.448 false 2.26,0.344 2.74,0.521 0.479,0.177 10 false *1 0.104,1.135 0.49,1.333 0.385,0.198 10 false SST 1.229,1.844 2.458,2.042 1.229,0.198 10 false 10 m or more
*1 Battery


Move SST at least 10 m (33 ft.) away from the front side window.


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



e.
H000544C01
1.313,0.854 0.646,1.333 false 0.49,1.333 0.729,1.51 0.24,0.177 10 false *1
*1 Plastic bag


Deploy the front seat side airbag.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

·

Do not apply water etc. to a front seat side airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 73910A 2.DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E06
0.145,0.656 0.521,0.857 0.376,0.201 10 SST 0.964,1.227 0.735,0.775 false 0.735,0.775 0.548,0.775 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820C18
1.917,1.313 1.979,1.677 false 2.51,0.802 2.719,0.802 false 1.865,1.677 2.198,1.875 0.333,0.198 10 false SST 2.781,0.719 3.115,0.917 0.333,0.198 10 false *1
*1 Battery


Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

SST
09082-00700  


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Remove the front seat side airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT SEAT SIDE AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·

Before removing the front seat side airbag assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.




c.
B104882C88
1.906,1.24 1.74,1.615 false 2.896,1 3.156,1.208 0.26,0.208 10 false A 1.625,1.656 1.854,1.854 0.229,0.198 10 false *a
*a Stripped Wire Harness Section


Using braided wire harness, tie down the front seat side airbag assembly to an unneeded tire.

Stripped Wire Harness Section:
Area Measurement
A 1.25 mm2 (0.0019 in.2) or more


CAUTION:

Do not use a wire harness that is too thin or any other object to tie the curtain shield airbag assembly because it may snap due to the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B283316

Install the 2 nuts to the front seat side airbag assembly.


ii.
B283318

Wind the wires around the stud bolts of the front seat side airbag assembly as shown in the illustration.


iii.
B286401E02
2.157,0.07 2.285,0.235 0.128,0.164 10 A 0.86,0.933 0.988,1.097 0.128,0.164 10 B

Position the front seat side airbag assembly inside the tire.

Tire Size:
Area Measurement
A 185 mm (7.28 in.)
B 360 mm (14.17 in.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the front seat side airbag assembly may break loose when the airbag is deployed.

·

Face the front seat side airbag assembly deployment surface toward the inside the tire to evenly distribute the force of deployment.



NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.




d.

Connect SST.

i.
B283317E01
0.585,1.443 0.584,1.717 false 0.426,1.725 0.750,1.864 0.324,0.138 10 SST

Connect the SST connector to the front seat side airbag assembly connector.

SST
09082-00820  



e.
B286400C02
2.608,0.514 2.877,0.707 0.269,0.193 10 *1 2.608,1.376 2.877,1.569 0.269,0.193 10 *1
*1 Tires (2 or more)


Place the tires.

i.

Place at least 2 tires under the tire to which the front seat side airbag assembly is tied.


ii.

Place at least 2 tires onto the tire to which the front seat side airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place SST connector under the tire because it could be damaged.

·

As the disc wheel will be marked by the airbag deployment, use a waste disc wheel.

·

As the tires will be marked by the airbag deployment, use waste tires.




iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




f.

Connect SST.

i.
B286402C02
1.007,2.622 1.911,2.802 0.904,0.181 10 10 m or more 0.339,2.415 0.339,2.718 false 0.182,2.718 0.526,2.886 0.344,0.168 10 SST 1.191,1.538 1.41,1.452 false 1.412,1.367 1.756,1.535 0.344,0.168 10 *1
*1 Battery


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (33 ft.) away from the airbag tied down to the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the tire to which the front seat side airbag assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.
H000544C02
1.313,0.854 0.646,1.333 false 0.49,1.333 0.729,1.51 0.24,0.177 10 false *1
*1 Plastic bag


Dispose of the front seat side airbag assembly.

CAUTION:
·

The front seat side airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat side airbag assembly with a deployed airbag.

·

Do not apply water etc. to a front seat side airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat side airbag assembly from the tire.


ii.

Place the front seat side airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.