Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › SFI SYSTEM › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _053310 1NR-FE ENGINE CONTROL _0258661 SFI SYSTEM J

1NR-FE ENGINE CONTROL  SFI SYSTEM  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one No. 1 ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A356985E11
6.094,0.938 6.708,1.135 0.615,0.198 10 false IGT1 6.115,2.542 6.729,2.74 0.615,0.198 10 false IGT2 6.135,4.198 6.75,4.396 0.615,0.198 10 false IGT3 6.125,5.729 6.74,5.927 0.615,0.198 10 false IGT4 5.875,0.844 6.229,1.063 0.354,0.219 10 false 16 5.865,2.469 6.198,2.667 0.333,0.198 10 false 15 5.875,4.073 6.188,4.271 0.313,0.198 10 false 14 5.865,5.635 6.177,5.833 0.313,0.198 10 false 13 4.594,0.938 5.208,1.135 0.615,0.198 10 false IGT1 4.604,2.563 5.219,2.76 0.615,0.198 10 false IGT2 4.583,4.167 5.198,4.365 0.615,0.198 10 false IGT3 4.594,5.74 5.208,5.938 0.615,0.198 10 false IGT4 4.958,0.844 5.115,1.042 0.156,0.198 10 false 3 4.958,4.094 5.115,4.292 0.156,0.198 10 false 3 4.958,2.49 5.115,2.688 0.156,0.198 10 false 3 4.948,5.635 5.104,5.833 0.156,0.198 10 false 3 6.417,6.76 6.875,6.958 0.458,0.198 10 false B46 6.427,6.958 6.885,7.156 0.458,0.198 10 false ECM 3.938,5.583 4.25,5.781 0.313,0.198 10 false +B 3.938,0.813 4.25,1.01 0.313,0.198 10 false +B 3.938,4.021 4.25,4.219 0.313,0.198 10 false +B 3.927,2.438 4.24,2.635 0.313,0.198 10 false +B 3.938,5.896 4.396,6.094 0.458,0.198 10 false GND 3.927,2.76 4.385,2.958 0.458,0.198 10 false GND 3.927,4.344 4.385,4.542 0.458,0.198 10 false GND 3.948,1.125 4.406,1.323 0.458,0.198 10 false GND 3.906,6.198 4.365,6.396 0.458,0.198 10 false B40 3.917,6.354 5.063,6.979 1.146,0.625 10 false No. 1 Ignition Coil (No. 4 Cylinder) 3.906,4.792 4.99,5.521 1.083,0.729 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.906,3.167 5.031,3.833 1.125,0.667 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.896,1.552 5.052,2.521 1.156,0.969 10 false No. 1 Ignition Coil (No. 1 Cylinder) 1.74,7.031 4.427,7.396 2.688,0.365 10 false *1: w/ Smart Entry and Start System 1.75,7.448 4.167,7.802 2.417,0.354 10 false *2: w/o Smart Entry and Start System 3.906,4.635 4.365,4.833 0.458,0.198 10 false B39 3.906,3 4.365,3.198 0.458,0.198 10 false B38 3.896,1.385 4.354,1.583 0.458,0.198 10 false B37 3.771,3.938 3.948,4.156 0.177,0.219 11 false 1 3.771,5.5 3.927,5.698 0.156,0.198 10 false 1 3.781,2.354 3.938,2.552 0.156,0.198 10 false 1 3.781,0.74 3.938,0.938 0.156,0.198 10 false 1 3.792,1.063 3.948,1.26 0.156,0.198 10 false 4 3.792,4.26 3.948,4.458 0.156,0.198 10 false 4 3.792,5.823 3.948,6.021 0.156,0.198 10 false 4 3.792,2.688 3.948,2.885 0.156,0.198 10 false 4 0.552,6.719 1.625,6.917 1.073,0.198 10 false Battery 0.354,5.448 0.969,5.646 0.615,0.198 10 false MAIN 0.365,6.115 1.438,6.313 1.073,0.198 10 false FL MAIN 0.344,4.875 0.802,5.073 0.458,0.198 10 false AM2 1.406,4.417 1.865,4.615 0.458,0.198 10 false F43 1.396,4.583 2.813,5.292 1.417,0.708 10 false Certification ECU (Smart Key ECU Assembly)*1 1.438,3.885 2.052,4.083 0.615,0.198 10 false IG1D 1.198,3.781 1.51,3.979 0.313,0.198 10 false 20 0.865,2.948 1.323,3.146 0.458,0.198 10 false F77 0.844,3.115 2.281,3.479 1.438,0.365 10 false No. 2 Ignition Relay*1 0.656,3.323 0.969,3.521 0.313,0.198 10 false *1 0.521,2.229 0.833,2.427 0.313,0.198 10 false *1 0.74,2.542 0.896,2.74 0.156,0.198 10 false 2 0.729,2.052 0.885,2.25 0.156,0.198 10 false 3 1.594,2.052 1.75,2.25 0.156,0.198 10 false 5 1.594,2.531 1.75,2.729 0.156,0.198 10 false 1 0.115,1.5 0.427,1.698 0.313,0.198 10 false *2 2.25,1.583 2.563,1.781 0.313,0.198 10 false *1 2.365,1.021 3.125,1.281 0.76,0.26 10 false IG2 NO. 1 1.885,0.938 2.198,1.135 0.313,0.198 10 false *2 1.5,0.76 1.958,0.958 0.458,0.198 10 false IG2 1.802,0.76 1.958,0.958 0.156,0.198 10 false 6 0.51,0.76 0.656,0.927 0.146,0.167 10 false 5 0.677,0.75 1.135,0.948 0.458,0.198 10 false AM2 0.583,1.156 0.896,1.354 0.313,0.198 10 false F7 0.583,1.313 2.146,2.073 1.563,0.76 10 false Ignition or Starter Switch Assembly*2 0.156,0.083 1.677,0.438 1.521,0.354 12 false for TMMIN Made:

A356985E16
6.094,0.938 6.708,1.135 0.615,0.198 10 false IGT1 6.115,2.542 6.729,2.74 0.615,0.198 10 false IGT2 6.135,4.198 6.75,4.396 0.615,0.198 10 false IGT3 6.125,5.729 6.74,5.927 0.615,0.198 10 false IGT4 5.875,0.844 6.229,1.063 0.354,0.219 10 false 16 5.865,2.469 6.198,2.667 0.333,0.198 10 false 15 5.875,4.073 6.188,4.271 0.313,0.198 10 false 14 5.865,5.635 6.177,5.833 0.313,0.198 10 false 13 4.594,0.938 5.208,1.135 0.615,0.198 10 false IGT1 4.604,2.563 5.219,2.76 0.615,0.198 10 false IGT2 4.583,4.167 5.198,4.365 0.615,0.198 10 false IGT3 4.594,5.74 5.208,5.938 0.615,0.198 10 false IGT4 4.958,0.844 5.115,1.042 0.156,0.198 10 false 3 4.958,4.094 5.115,4.292 0.156,0.198 10 false 3 4.958,2.49 5.115,2.688 0.156,0.198 10 false 3 4.948,5.635 5.104,5.833 0.156,0.198 10 false 3 6.417,6.76 6.875,6.958 0.458,0.198 10 false B46 6.427,6.958 6.885,7.156 0.458,0.198 10 false ECM 3.938,5.583 4.25,5.781 0.313,0.198 10 false +B 3.938,0.813 4.25,1.01 0.313,0.198 10 false +B 3.938,4.021 4.25,4.219 0.313,0.198 10 false +B 3.927,2.438 4.24,2.635 0.313,0.198 10 false +B 3.938,5.896 4.396,6.094 0.458,0.198 10 false GND 3.927,2.76 4.385,2.958 0.458,0.198 10 false GND 3.927,4.344 4.385,4.542 0.458,0.198 10 false GND 3.948,1.125 4.406,1.323 0.458,0.198 10 false GND 3.906,6.198 4.365,6.396 0.458,0.198 10 false B40 3.917,6.354 5.063,6.979 1.146,0.625 10 false No. 1 Ignition Coil (No. 4 Cylinder) 3.906,4.792 4.99,5.521 1.083,0.729 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.906,3.167 5.031,3.833 1.125,0.667 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.896,1.552 5.052,2.521 1.156,0.969 10 false No. 1 Ignition Coil (No. 1 Cylinder) 1.74,7.031 4.427,7.396 2.688,0.365 10 false *1: w/ Smart Entry and Start System 1.75,7.448 4.167,7.802 2.417,0.354 10 false *2: w/o Smart Entry and Start System 3.906,4.635 4.365,4.833 0.458,0.198 10 false B39 3.906,3 4.365,3.198 0.458,0.198 10 false B38 3.896,1.385 4.354,1.583 0.458,0.198 10 false B37 3.771,3.938 3.948,4.156 0.177,0.219 11 false 1 3.771,5.5 3.927,5.698 0.156,0.198 10 false 1 3.781,2.354 3.938,2.552 0.156,0.198 10 false 1 3.781,0.74 3.938,0.938 0.156,0.198 10 false 1 3.792,1.063 3.948,1.26 0.156,0.198 10 false 4 3.792,4.26 3.948,4.458 0.156,0.198 10 false 4 3.792,5.823 3.948,6.021 0.156,0.198 10 false 4 3.792,2.688 3.948,2.885 0.156,0.198 10 false 4 0.552,6.719 1.625,6.917 1.073,0.198 10 false Battery 0.354,5.448 0.969,5.646 0.615,0.198 10 false MAIN 0.365,6.115 1.438,6.313 1.073,0.198 10 false FL MAIN 0.344,4.875 0.802,5.073 0.458,0.198 10 false AM2 1.406,4.417 1.865,4.615 0.458,0.198 10 false F43 1.396,4.583 2.813,5.292 1.417,0.708 10 false Certification ECU (Smart Key ECU Assembly)*1 1.438,3.885 2.052,4.083 0.615,0.198 10 false IG1D 1.198,3.781 1.51,3.979 0.313,0.198 10 false 20 1.042,2.948 1.5,3.156 0.458,0.208 10 false IG2*1 0.656,3.323 0.969,3.521 0.313,0.198 10 false *1 0.521,2.229 0.833,2.427 0.313,0.198 10 false *1 0.74,2.542 0.896,2.74 0.156,0.198 10 false 2 0.729,2.052 0.885,2.25 0.156,0.198 10 false 3 1.594,2.052 1.75,2.25 0.156,0.198 10 false 5 1.594,2.531 1.75,2.729 0.156,0.198 10 false 1 0.115,1.5 0.427,1.698 0.313,0.198 10 false *2 2.25,1.583 2.563,1.781 0.313,0.198 10 false *1 2.365,1.021 3.125,1.281 0.76,0.26 10 false IG2 NO. 1 1.885,0.938 2.198,1.135 0.313,0.198 10 false *2 1.5,0.76 1.958,0.958 0.458,0.198 10 false IG2 1.802,0.76 1.958,0.958 0.156,0.198 10 false 6 0.51,0.76 0.656,0.927 0.146,0.167 10 false 5 0.677,0.75 1.135,0.948 0.458,0.198 10 false AM2 0.583,1.156 0.896,1.354 0.313,0.198 10 false F7 0.583,1.313 2.146,2.073 1.563,0.76 10 false Ignition or Starter Switch Assembly*2 0.313,0.115 1.656,0.396 1.344,0.281 12 false for TMT Made:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
a.
A260712C10
0.521,0.469 0.979,0.74 0.458,0.271 0.521,0.792 0.979,1.063 0.458,0.271 0.521,1.115 0.979,1.385 0.458,0.271 0.521,1.438 0.979,1.708 0.458,0.271 2.031,1.177 2.229,1.635 true 1.417,1.177 1.313,1.615 true 0.188,0.125 0.448,0.302 0.26,0.177 10 false *a 0.604,0.51 0.906,0.688 0.302,0.177 10 false B37 0.604,0.844 0.906,1.021 0.302,0.177 10 false B38 0.604,1.167 0.906,1.344 0.302,0.177 10 false B39 0.615,1.49 0.917,1.667 0.302,0.177 10 false B40 2.083,1.667 2.438,1.833 0.354,0.167 10 false GND 1.229,1.635 1.458,1.802 0.229,0.167 10 false +B
*a Front view of wire harness connector
(to No. 1 Ignition Coil)


Disconnect the No. 1 ignition coil connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B37-1 (+B) - B37-4 (GND) Ignition switch ON 11 to 14 V
B38-1 (+B) - B38-4 (GND) Ignition switch ON 11 to 14 V
B39-1 (+B) - B39-4 (GND) Ignition switch ON 11 to 14 V
B40-1 (+B) - B40-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
a.

Disconnect the B37, B38, B39 and B40 No. 1 ignition coil connectors.


b.

Disconnect the B46 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-3 (IGT1) - B46-16 (IGT1) Always Below 1 Ω
B38-3 (IGT2) - B46-15 (IGT2) Always Below 1 Ω
B39-3 (IGT3) - B46-14 (IGT3) Always Below 1 Ω
B40-3 (IGT4) - B46-13 (IGT4) Always Below 1 Ω
B37-3 (IGT1) or B46-16 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
B38-3 (IGT2) or B46-15 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
B39-3 (IGT3) or B46-14 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
B40-3 (IGT4) or B46-13 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
a.

Disconnect the B37, B38, B39 and B40 No. 1 ignition coil connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-4 (GND) - Body ground Always Below 1 Ω
B38-4 (GND) - Body ground Always Below 1 Ω
B39-4 (GND) - Body ground Always Below 1 Ω
B40-4 (GND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for TMMIN Made with Smart Entry and Start System) A
OK (for TMT Made with Smart Entry and Start System) B
OK (w/o Smart Entry and Start System) C
NG D



A

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 2 IGNITION RELAY)

B

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IG2 RELAY)

C

6.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IGNITION OR STARTER SWITCH ASSEMBLY)

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 2 IGNITION RELAY)
a.

Disconnect the B37, B38, B39 and B40 No. 1 ignition coil connectors.


b.

Remove the No. 2 ignition relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (+B) - F77-5 (No. 2 ignition relay holder) Always Below 1 Ω
B38-1 (+B) - F77-5 (No. 2 ignition relay holder) Always Below 1 Ω
B39-1 (+B) - F77-5 (No. 2 ignition relay holder) Always Below 1 Ω
B40-1 (+B) - F77-5 (No. 2 ignition relay holder) Always Below 1 Ω
B37-1 (+B) or F77-5 (No. 2 ignition relay holder) - Body ground and other terminals Always 10 kΩ or higher
B38-1 (+B) or F77-5 (No. 2 ignition relay holder) - Body ground and other terminals Always 10 kΩ or higher
B39-1 (+B) or F77-5 (No. 2 ignition relay holder) - Body ground and other terminals Always 10 kΩ or higher
B40-1 (+B) or F77-5 (No. 2 ignition relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IG2 RELAY)
a.

Disconnect the B37, B38, B39 and B40 No. 1 ignition coil connectors.


b.

Remove the IG2 relay from the No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (+B) - 5 (IG2 relay holder) Always Below 1 Ω
B38-1 (+B) - 5 (IG2 relay holder) Always Below 1 Ω
B39-1 (+B) - 5 (IG2 relay holder) Always Below 1 Ω
B40-1 (+B) - 5 (IG2 relay holder) Always Below 1 Ω
B37-1 (+B) or 5 (IG2 relay holder) - Body ground and other terminals Always 10 kΩ or higher
B38-1 (+B) or 5 (IG2 relay holder) - Body ground and other terminals Always 10 kΩ or higher
B39-1 (+B) or 5 (IG2 relay holder) - Body ground and other terminals Always 10 kΩ or higher
B40-1 (+B) or 5 (IG2 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the B37, B38, B39 and B40 No. 1 ignition coil connectors.


b.

Disconnect F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
B37-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B38-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B39-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B40-1 (+B) - F7-6 (IG2) Always Below 1 Ω
B37-1 (+B) or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B38-1 (+B) or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B39-1 (+B) or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B40-1 (+B) or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR