The atmospheric pressure sensor detects the atmospheric pressure. By detecting the atmospheric pressure, it is possible to calculate brake negative pressure values reflecting the effects of air pressure fluctuations caused by altitude changes.
When the ECU determines that there is a malfunction in the input signal from the atmospheric pressure sensor, it stores DTC C147A,C147B.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| C147A | Atmospheric Pressure Sensor Circuit Low | All of the following conditions are met (1 trip detection logic): 1.
After 2 seconds or more elapse after turn the ignition switch to ON. 2.
After 2 seconds or more elapse after starting the engine. 3.
The atmospheric pressure sensor input voltage is less than 0.5 V for 1.2 seconds or more. |
·
Wire harness or connector ·
Atmospheric pressure sensor ·
ECM |
Does not come on | DTC Stored |
| C147B | Atmospheric Pressure Sensor Circuit High | All of the following conditions are met (1 trip detection logic): 1.
After 2 seconds or more elapse after turn the ignition switch to ON. 2.
After 2 seconds or more elapse after starting the engine. 3.
The atmospheric pressure sensor input voltage is more than 4.5 V for 1.2 seconds or more (1 trip detection logic). |
·
Wire harness or connector ·
Atmospheric pressure sensor ·
ECM |
Does not come on | DTC Stored |
When either of the DTCs have been stored, the ECM enters fail-safe mode. During fail-safe mode operation, to prevent the brake vacuum pressure from decreasing when driving at high altitudes, the air conditioner turns off more frequently*1. Fail-safe mode operation continues until the ECM condition returns to normal.
*1: w/ Air Conditioning System
DTCs for the SFI system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Start the engine and allow it to idle for 15 seconds or more.
Turn the ignition switch off.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure.
Read the values displayed on the GTS.
Approximately the same as ambient atmospheric pressure.
Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)].
For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: C147A or C147B.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the atmospheric pressure sensor.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ATMOSPHERIC PRESSURE SENSOR>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for CVT |
| *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F130-33 (VHAC) - F130-34 (EHAC) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F130 ECM connector.
Disconnect the F117 atmospheric pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-33 (VHAC) - F117-3 (VC) | Always | Below 1 Ω |
| F130-25 (HAC) - F117-2 (PB) | Always | Below 1 Ω |
| F130-34 (EHAC) - F117-1 (E2) | Always | Below 1 Ω |
| F130-33 (VHAC) or F117-3 (VC) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-25 (HAC) or F117-2 (PB) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-34 (EHAC) or F117-1 (E2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-33 (VHAC) - F117-3 (VC) | Always | Below 1 Ω |
| F130-25 (HAC) - F117-2 (HAC) | Always | Below 1 Ω |
| F130-34 (EHAC) - F117-1 (E2) | Always | Below 1 Ω |
| F130-33 (VHAC) or F117-3 (VC) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-25 (HAC) or F117-2 (HAC) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-34 (EHAC) or F117-1 (E2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the atmospheric pressure sensor.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ATMOSPHERIC PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Clear the DTC.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure.
| Tester Display |
|---|
| Atmosphere Pressure |
Read the values displayed on the GTS.
Approximately the same as ambient atmospheric pressure.
Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)].
For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC C147A or C147B is output | B |
A
B