Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › from 2017.10
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0092744 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not apply voltage to any terminals except terminals 1 (GND) and 2 (B), to avoid damaging the pulse sensor inside the motor.


·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor assembly LH and front door window regulator assembly LH onto the door.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

Hide 85720E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for LHD)

a.

Check the operation.

i.
B347327C02
2.281,2.323 1.802,2.625 true 2.302,2.615 1.76,2.771 true 2.302,3.063 1.865,3.01 true 1.469,2.979 1.135,2.979 true 1.063,2.552 1.552,2.635 true 2.635,1.927 1.927,1.5 true 0.542,1.531 0.854,1.729 0.313,0.198 10 false *c 0.656,1.823 0.969,2.021 0.313,0.198 10 false *b 1.229,2.167 1.542,2.365 0.313,0.198 10 false *a 2.688,1.865 3,2.063 0.313,0.198 10 false *1 0.948,2.469 1.104,2.635 0.156,0.167 10 false B 0.917,2.906 1.146,3.104 0.229,0.198 10 false UP 2.344,2.25 2.781,2.448 0.438,0.198 10 false GND 2.344,2.531 2.781,2.729 0.438,0.198 10 false AUTO 2.344,2.99 3.063,3.167 0.719,0.177 10 false DOWN
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise


Apply battery voltage to the motor connector according to the table below.

OK:
Switch Condition Measurement Condition Specified Condition
Manual Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 10 (UP)
Motor gear rotates clockwise
Auto Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 10 (UP)
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.



Hide 85720E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for RHD)

a.

Check the operation.

i.
B342352C02
1.188,1.417 1.594,1.917 true 2.344,1.458 2.656,1.656 0.313,0.198 10 false *b 2.208,1.771 2.521,1.969 0.313,0.198 10 false *c 1.594,1.938 1.906,2.135 0.313,0.198 10 false *1 2.396,0.094 2.708,0.292 0.313,0.198 10 false *a
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Counterclockwise
*c Clockwise


Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.



Hide 85710E 3.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for LHD)

a.

Check the operation.

i.
B347328C02
1.542,1.396 1.177,1.896 true 2.417,0.104 2.729,0.302 0.313,0.198 10 false *a 0.26,1.469 0.573,1.667 0.313,0.198 10 false *c 0.385,1.719 0.698,1.917 0.313,0.198 10 false *b 1.094,1.906 1.323,2.083 0.229,0.177 10 false *1
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Counterclockwise
*c Clockwise


Apply battery voltage to the motor connector according to the table below.

Standard:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.



Hide 85720E 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for RHD)

a.

Check the operation.

i.
B342351C03
0.979,2.031 1.479,1.5 true 1.083,2.5 1.552,2.688 true 1.802,2.625 2.25,2.333 true 1.865,3 2.167,3.167 true 1.75,2.792 2.198,2.521 true 1.115,2.979 1.49,2.979 true 2.677,1.896 2.99,2.094 0.313,0.198 10 false *c 2.781,1.51 3.094,1.708 0.313,0.198 10 false *b 0.813,2.01 1.125,2.208 0.313,0.198 10 false *1 1.167,2.156 1.479,2.354 0.313,0.198 10 false *a 0.958,2.396 1.115,2.594 0.156,0.198 10 false B 2.281,2.219 2.74,2.49 0.458,0.271 10 false GND 2.198,3.115 2.74,3.354 0.542,0.24 10 false DOWN 2.25,2.448 2.708,2.719 0.458,0.271 10 false AUTO 0.896,2.906 1.198,3.208 0.302,0.302 10 false UP
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Counterclockwise
*c Clockwise


Apply battery voltage to the motor connector according to the table below.

OK:
Switch Condition Measurement Condition Specified Condition
Manual Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
Motor gear rotates clockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 10 (UP)
Motor gear rotates counterclockwise
Auto Operation Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
Motor gear rotates clockwise
Battery positive (+) → Terminal 2 (B)
Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 10 (UP)
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.