Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR › from 2017.10
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0116750 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E373237C01
1.354,0.635 1.76,1.167 1.76,1.167 2.167,0.625 true 1.698,1.188 2.01,1.385 0.313,0.198 10 false *a
*a Lip of Rear Wiper Motor Grommet


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with MP grease and the grooves on the lip are filled with MP grease.



b.
E373236C01
0.604,0.063 0.917,0.26 0.313,0.198 10 false *a 0.844,0.052 1.156,0.25 0.313,0.198 10 false *a
*a 5°


Install the rear wiper motor grommet as shown in the illustration.


Hide 76801 2.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 85110R 3.INSTALL REAR WIPER MOTOR ASSEMBLY

a.
E373234E02
0.667,0.26 0.969,0.219 true 2.823,0.646 3.042,0.51 true 1.458,1.177 1.698,1.313 true 1.052,0.135 1.208,0.333 0.156,0.198 10 false B 3.115,0.438 3.271,0.635 0.156,0.198 10 false B 1.76,1.229 1.917,1.427 0.156,0.198 10 false A 0.177,0.5 0.292,0.667 0.115,0.167 10 true 2 1.604,1.531 1.719,1.698 0.115,0.167 10 true 1 3.083,0.906 3.198,1.073 0.115,0.167 10 true 3

Set the rear wiper motor assembly in place and temporarily tighten the bolt A.


b.

Temporarily tighten the 2 bolts B.


c.

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Connect the connector and engage the clamp.


Hide 4.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
E226523C17
1.198,1.052 0.667,0.646 true 0.479,0.531 0.792,0.781 0.313,0.25 10 false *a
*a Wiper Arm Serration


When reusing the rear wiper arm and blade assembly:

i.

Clean the wiper arm serrations.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E373238C01
1.99,1.385 2.302,1.385 false 2.365,1.281 2.677,1.479 0.313,0.198 10 false *a
*a Wiper Pivot Serration


When reusing the rear wiper motor assembly:

i.

Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.




c.

Operate the wiper, and then stop the rear wiper motor assembly in the automatic stop position.


d.
E373680C01
2.24,2.604 1.979,2.406 false 1.781,2.281 2.094,2.479 0.313,0.198 10 false *a 2.854,2.365 3.167,2.563 0.313,0.198 10 false a 2.865,2.667 3.177,2.865 0.313,0.198 10 false a
*a Alignment Mark


Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the rear wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 10.0 mm (0.394 in.)



e.

Turn the engine switch on (IG).


f.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not contact the vehicle body.


g.

Turn the engine switch off.


h.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


Hide 85292A 5.INSTALL REAR WIPER ARM HEAD CAP

a.

Engage the 2 claws and 2 hinges to install the rear wiper arm head cap.


Hide 6.INSTALL REAR LIGHT ASSEMBLY (for Hatchback)