Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BACK DOOR OUTSIDE GARNISH › from 2017.10
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0118073 BACK DOOR OUTSIDE GARNISH A

EXTERIOR PANELS / TRIM  BACK DOOR OUTSIDE GARNISH  INSTALLATION  


PROCEDURE

Hide 76825 1.INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR

HINT:

When installing the back door outside garnish protector, heat the luggage compartment door outside garnish Sub-assembly using a heat light.


CAUTION:
·
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

Standard:
Item Temperature
Luggage Compartment Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the luggage compartment door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish protector installation surface with a non-residue solvent.


b.

Apply primer to the back door outside garnish protector installation area on the luggage compartment door outside garnish sub-assembly.

NOTICE:

Apply primer evenly so that there are no uncoated areas.



c.

Remove the peeling paper on a new back door outside garnish protector while making sure not to touch the adhesive surface.


d.
B484328

Install the back door outside garnish protector as shown in the illustration.

NOTICE:
·

Press the double-sided tape on the back door outside garnish protector firmly to ensure proper adhesion.

·

After the primer dries (3 minutes or more), install the back door outside garnish protector.

·

After applying primer, reapply primer after 24 hours elapse.




Hide 76816 2.INSTALL BACK DOOR OUTSIDE GARNISH LOWER MOULDING LH

HINT:

When installing the back door outside garnish lower moulding LH, heat the luggage compartment door outside garnish sub-assembly using a heat light.


CAUTION:
·
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

Standard:
Item Temperature
Luggage Compartment Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the luggage compartment door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish lower moulding LH installation surface with a non-residue solvent.


b.

Apply primer to the back door outside garnish lower moulding LH installation area on the luggage compartment door outside garnish sub-assembly.

NOTICE:

Apply primer evenly so that there are no uncoated areas.



c.

Remove the peeling paper on a new back door outside garnish lower moulding LH while making sure not to touch the adhesive surface.


d.
B484308

Install the back door outside garnish lower moulding LH as shown in the illustration.

NOTICE:
·

Press the double-sided tape on the back door outside garnish lower moulding LH firmly to ensure proper adhesion.

·

After the primer dries (3 minutes or more), install the back door outside garnish lower moulding LH.

·

After applying primer, reapply primer after 24 hours elapse.




Hide 76815 3.INSTALL BACK DOOR OUTSIDE GARNISH LOWER MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 76801 4.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

a.

Engage the 6 clips to install the back door outside garnish sub-assembly.


b.

Install the 4 bolts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 85110R 5.INSTALL REAR WIPER MOTOR ASSEMBLY