Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO & VISUAL SYSTEM › from 2017.10
RM30M0E _56 Audio / Visual / Telematics _017106 AUDIO / VIDEO _0084785 AUDIO & VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO & VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E361242E11
1.667,1.063 2.125,1.26 0.458,0.198 10 false SPD 5.198,1.063 5.656,1.26 0.458,0.198 10 false +S 5.177,1.781 5.635,1.979 0.458,0.198 10 false F38 1.146,1.792 1.604,1.99 0.458,0.198 10 false F142 1.135,1.979 2.083,2.385 0.948,0.406 10 false Radio Receiver Assembly 5.167,1.958 6.354,2.479 1.188,0.521 10 false Combination Meter Assembly 3.792,1.448 4.938,1.698 1.146,0.25 10 false to Other ECUs 4.948,0.948 5.323,1.167 0.375,0.219 10 false 18 2.052,0.938 2.427,1.156 0.375,0.219 10 false 17


PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E370193C06
1.438,0.292 1.896,0.573 0.458,0.281 2.323,1.938 2.177,1.406 true 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 2.26,1.969 2.583,2.208 0.323,0.24 10 false SPD 1.51,0.354 2.01,0.635 0.5,0.281 10 false F142 2.938,3.813 3.302,4.063 0.365,0.25 10 false GND 1.167,4.073 1.531,4.323 0.365,0.25 10 false (A)
*a Component with harness connected
(Radio Receiver Assembly)


Check the input waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F142-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F142-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E370192C03
1.448,0.385 1.885,0.646 0.438,0.26 0.833,1.917 1.104,1.333 true 0.198,0.188 0.51,0.385 0.313,0.198 10 false *a 1.563,0.427 2.042,0.719 0.479,0.292 10 false F38 0.719,1.948 1.031,2.146 0.313,0.198 10 false +S 2.938,3.823 3.313,4.063 0.375,0.24 10 false GND 1.177,4.073 1.552,4.313 0.375,0.24 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F38-18 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F38-18 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F142 radio receiver assembly connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-17 (SPD) -F38-18 (+S) Always Below 1 Ω
F142-17 (SPD) -Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR