Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on (w/ air conditioning system).
1.DRAIN ENGINE COOLANT
81150
2.REMOVE HEADLIGHT ASSEMBLY LH (for TMMIN Made)
81150
3.REMOVE HEADLIGHT ASSEMBLY RH (for TMMIN Made)
Use the same procedure as for the LH side.
81150
4.REMOVE HEADLIGHT ASSEMBLY LH (for TMT Made)
81150
5.REMOVE HEADLIGHT ASSEMBLY RH (for TMT Made)
Use the same procedure as for the LH side.
89173
6.REMOVE FRONT AIRBAG SENSOR (w/ Airbag System)
for TMMIN Made:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR(for TMMIN Made)>REMOVAL
for TMT Made:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR(for TMT Made)>REMOVAL
53510
7.REMOVE HOOD LOCK ASSEMBLY (for TMMIN Made)
53510
8.REMOVE HOOD LOCK ASSEMBLY (for TMT Made)
w/ Engine Hood Courtesy Switch:
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL
w/o Engine Hood Courtesy Switch:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY(for RHD)>REMOVAL
53215B
9.REMOVE HOOD LOCK SUPPORT
Disengage the clamp to disconnect the wire harness from the hood lock support.
Remove the 2 bolts and hood lock support from the radiator support assembly.
88891H
10.REMOVE NO. 1 COOLER COVER (for TMMIN Made)
88891H
11.REMOVE NO. 1 COOLER COVER (for TMT Made)
53216A
12.REMOVE UPPER RADIATOR SUPPORT
Disengage the clamp to separate the hood lock control cable assembly from the upper radiator support.
Disengage the 3 clamps to disconnect the wire harness from the upper radiator support.
Disconnect the low pitched horn assembly connector.
Remove the 4 bolts and upper radiator support from the radiator support assembly.
13.DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reservoir tank hose from the radiator assembly.
16571C
14.DISCONNECT NO. 1 RADIATOR HOSE
Slide the hose clip and disconnect the No. 1 radiator hose from the radiator assembly.
16572D
15.DISCONNECT NO. 2 RADIATOR HOSE
Slide the hose clip and disconnect the No. 2 radiator hose from the radiator assembly.
16400
16.REMOVE RADIATOR ASSEMBLY (w/ Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Disengage the 2 claws and 2 guides to separate the cooler condenser assembly from the radiator assembly.
While tilting the cooler condenser assembly toward the front of the vehicle, separate the cooler condenser assembly from the radiator assembly.
Remove the radiator assembly together with fan shroud from the vehicle.
Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.
16400
17.REMOVE RADIATOR ASSEMBLY (w/o Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Remove the radiator assembly together with fan shroud from the vehicle.
16711
18.REMOVE FAN SHROUD
Disengage the 2 claws and 3 guides to remove the fan shroud from the radiator assembly.
16523A
19.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
20.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.
21.REMOVE RADIATOR DRAIN COCK PLUG
Remove the radiator drain cock plug from the radiator assembly.
Replace the O-ring if it is damaged.
16561
22.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.
Remove the No. 1 radiator to support seal for upper side from the radiator assembly.
Remove the No. 1 radiator to support seal for lower side from the radiator assembly.