Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  C1514  Torque Sensor Power Supply Voltage  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C1514 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1514 Torque Sensor Power Supply Voltage Diagnosis Condition: IG ON
Malfunction Status: TRQV voltage is less than 4.5 V or more than 5.5 V.
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again -

WIRING DIAGRAM

C375648E08
0.26,3.021 2.698,3.375 2.438,0.354 10 false Torque Sensor (Electric Power Steering Column Sub-assembly) 5.865,0.604 6.177,0.802 0.313,0.198 10 false 5V 5.115,0.823 5.729,1.021 0.615,0.198 10 false TRQV 4.896,0.813 5.052,1.01 0.156,0.198 10 false 8 4.885,2.229 5.042,2.427 0.156,0.198 10 false 2 5.104,2.24 5.719,2.438 0.615,0.198 10 false TRQG 4.802,3.115 7.156,3.406 2.354,0.292 10 false Power Steering ECU Assembly 4.813,2.958 5.125,3.156 0.313,0.198 10 false z5

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION



PROCEDURE

1.INSPECT TORQUE SENSOR (ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY) (CHECK FOR SHORT)
a.

Disconnect the z5 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-8 (TRQV) - Body ground Always 10 kΩ or higher
z5-8 (TRQV) - z5-2 (TRQG) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING ECU ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

2.INSPECT POWER STEERING ECU ASSEMBLY (POWER SOURCE OF TORQUE SENSOR)
a.

Start the engine.


b.
E316281C19
0.583,0.667 1.083,0.917 0.5,0.25 0.865,1.854 0.448,2.958 true 0.865,2.104 1.26,2.979 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.75,0.698 1.021,0.854 0.271,0.156 10 false z5 0.24,3 0.719,3.188 0.479,0.188 10 false TRQG 1.083,3 1.531,3.229 0.448,0.229 10 false TRQV
*a Component with harness connected
(Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z5-8 (TRQV) - z5-2 (TRQG) Engine start 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

NG

REPLACE POWER STEERING ECU ASSEMBLY