Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag ECU assembly and lower No. 1 instrument panel airbag assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1860/64 Short in Driver Side Knee Airbag Squib Circuit
·

The airbag ECU assembly detects a line short in the driver side knee airbag squib during primary check.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag ECU assembly


Applies to check mode
B1861/64 Open in Driver Side Knee Airbag Squib Circuit
·

The airbag ECU assembly detects an open in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag ECU assembly


Applies to check mode
B1862/64 Short to GND in Driver Side Knee Airbag Squib Circuit
·

The airbag ECU assembly detects a short to ground in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag ECU assembly


Applies to check mode
B1863/64 Short to B+ in Driver Side Knee Airbag Squib Circuit
·

The airbag ECU assembly detects a short to B+ in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C381305E15
2.031,1.073 2.49,1.271 0.458,0.198 10 false DK+ 2.073,1.885 2.531,2.083 0.458,0.198 10 false DK- 2.417,1.073 2.604,1.292 0.188,0.219 10 false 1 2.427,1.896 2.615,2.115 0.188,0.219 10 false 2 4.51,1.063 4.698,1.281 0.188,0.219 10 false 9 4.427,1.906 4.615,2.125 0.188,0.219 10 false 10 4.729,1.146 5.188,1.344 0.458,0.198 10 false DK+ 4.729,2 5.188,2.198 0.458,0.198 10 false DK- 4.771,3.01 5.229,3.208 0.458,0.198 10 false F21 4.76,3.167 6.708,3.417 1.948,0.25 10 false Airbag ECU Assembly 0.594,2.521 1.052,2.719 0.458,0.198 10 false F151 0.573,2.688 3.479,3.167 2.906,0.479 10 false Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib)

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238350C09
0.521,1.021 0.521,1.635 false 1.375,0.896 1.542,0.479 false 0.646,0.875 0.865,1.167 0.219,0.292 10 false D 1.052,0.875 1.417,1.281 0.365,0.406 10 false C 1.625,0.875 1.938,1.26 0.313,0.385 10 false B 2.021,0.875 2.281,1.26 0.26,0.385 10 false A 2.469,1.188 2.771,1.625 0.302,0.438 10 false *2 0.448,1.656 0.896,1.99 0.448,0.333 10 false *1 1.615,0.385 1.854,0.594 0.24,0.208 10 false *3
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
a.
C241757C12
0.417,2.26 0.917,2.5 0.5,0.24 0.698,0.698 0.698,1.094 false 1.844,2.281 2.021,2.281 false 0.625,1.094 0.979,1.396 0.354,0.302 10 false *1 2.271,0.865 2.615,1.198 0.344,0.333 10 false *2 1.823,0.552 2.156,0.906 0.333,0.354 10 false A 1.667,0.542 2.083,1.01 0.417,0.469 10 false B 1.167,0.542 1.594,0.99 0.427,0.448 10 false C 0.823,0.542 1.219,0.99 0.396,0.448 10 false D 0.521,2.302 0.938,2.531 0.417,0.229 10 false F151 2.052,2.198 2.521,2.5 0.469,0.302 10 false SST 0.313,1.771 0.635,2.094 0.323,0.323 10 false *a
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the lower No. 1 instrument panel airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
C241758C13
0.333,2.417 0.833,2.667 0.5,0.25 0.688,0.698 0.688,1.094 false 1.438,2.188 1.719,2.188 true 0.948,2.188 1.219,2.188 true 1.417,0.552 1.25,0.219 false 0.625,1.094 1.073,1.427 0.448,0.333 10 false *1 2.271,0.823 2.615,1.125 0.344,0.302 10 false *2 1.885,0.542 2.208,0.833 0.323,0.292 10 false A 1.573,0.542 1.865,0.802 0.292,0.26 10 false B 1.135,0.542 1.552,0.927 0.417,0.385 10 false C 0.823,0.542 1.281,0.854 0.458,0.313 10 false D 0.427,2.448 0.865,2.708 0.438,0.26 10 false F151 1.76,2.104 2.188,2.406 0.427,0.302 10 false DK- 0.646,2.104 1.167,2.469 0.521,0.365 10 false DK+ 0.25,1.792 0.573,2.156 0.323,0.365 10 false *a 1.052,0.125 1.385,0.51 0.333,0.385 10 false *3
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F151-1 (DK+) - Body ground Ignition switch ON Below 1 V
F151-2 (DK-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F151-1 (DK+) - F151-2 (DK-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F151-1 (DK+) - Body ground Always 1 MΩ or higher
F151-2 (DK-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F151-1 (DK+) - F151-2 (DK-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238353C01
0.802,0.833 0.802,1.156 false 0.938,0.708 1.542,1.438 0.604,0.729 10 false D 1.083,0.708 1.49,1.177 0.406,0.469 10 false C 1.594,0.708 1.885,1.094 0.292,0.385 10 false B 1.75,0.708 2.073,1 0.323,0.292 10 false A 2.188,1.021 2.49,1.354 0.302,0.333 10 false *2 0.74,1.167 1.115,1.521 0.375,0.354 10 false *1
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag ECU Assembly


Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG