Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090850 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Result Proceed to
OK (for TMMIN Made) A
OK (for TMT Made) B
NG C



A

2.INSPECT NO. 1 IGNITION RELAY

B

9.INSPECT NO. 1 IGNITION RELAY

C

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.INSPECT NO. 1 IGNITION RELAY
a.

Remove the No. 1 ignition relay.


b.
B344996E02
1.969,0.906 2.302,1.083 true 2.427,0.24 2.604,0.604 true 2.917,1.094 3.229,0.917 true 2.615,1.635 2.823,1.917 true 3.26,0.823 3.417,1.021 0.156,0.198 10 false 1 2.302,0.135 2.458,0.333 0.156,0.198 10 false 3 1.844,0.823 2,1.021 0.156,0.198 10 false 2 2.813,1.958 2.969,2.156 0.156,0.198 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 IGNITION RELAY)

NG

REPLACE NO. 1 IGNITION RELAY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 IGNITION RELAY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F76 No. 1 ignition relay connector.


c.

Disconnect the F77 No. 2 ignition relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - F76-1 Always Below 1 Ω
F76-2 - Body ground Always Below 1 Ω
F43-20 (IG1D) or F76-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 IGNITION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 IGNITION RELAY)
a.

Remove the No. 1 ignition relay.


b.
B344995C02
0.583,0.823 0.948,1.052 0.365,0.229 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.646,0.854 0.958,1.052 0.313,0.198 10 false F76
*a Front view of harness connector
(to No. 1 Ignition Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F76-5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 2 IGNITION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT NO. 2 IGNITION RELAY
a.

Remove the No. 2 ignition relay.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 IGNITION RELAY)

NG

REPLACE NO. 2 IGNITION RELAY

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 IGNITION RELAY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F77 No. 2 ignition relay connector.


c.

Disconnect the F76 No. 1 ignition relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - F77-2 Always Below 1 Ω
F77-1 - Body ground Always Below 1 Ω
F43-20 (IG1D) or F77-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 2 IGNITION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 2 IGNITION RELAY)
a.

Remove the No. 2 ignition relay.


b.
B287559C03
0.781,1.135 1.167,1.354 0.385,0.219 0.094,0.125 0.406,0.323 0.313,0.198 10 false *a 0.854,1.167 1.313,1.365 0.458,0.198 10 false F77
*a Front view of wire harness connector
(to No. 2 Ignition Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the certification ECU (smart key ECU assembly) connector.

B342590C07
2.833,0.417 3.25,0.667 0.417,0.25 2.563,1.417 2.865,2.229 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 2.917,0.438 3.375,0.635 0.458,0.198 10 false F43 2.74,2.26 3.281,2.51 0.542,0.25 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT NO. 1 IGNITION RELAY
a.

Remove the No. 1 ignition relay.


b.
B344996E02
1.969,0.906 2.302,1.083 true 2.427,0.24 2.604,0.604 true 2.917,1.094 3.229,0.917 true 2.615,1.635 2.823,1.917 true 3.26,0.823 3.417,1.021 0.156,0.198 10 false 1 2.302,0.135 2.458,0.333 0.156,0.198 10 false 3 1.844,0.823 2,1.021 0.156,0.198 10 false 2 2.813,1.958 2.969,2.156 0.156,0.198 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))

NG

REPLACE NO. 1 IGNITION RELAY

10.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))
a.

Remove the No. 1 ignition relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377752C01
0.375,0.26 0.75,0.5 0.375,0.24 12 false *A 3.833,0.26 4.208,0.5 0.375,0.24 12 false *B 1.573,0.354 1.948,0.594 0.375,0.24 10 false *2 4.333,0.833 4.708,1.073 0.375,0.24 10 false *1 4.938,0.375 5.313,0.615 0.375,0.24 10 false *2 0.698,0.531 1.073,0.771 0.375,0.24 10 false *1
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 1 Ignition Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 ignition relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION RELAY - BODY GROUND)
a.

Remove the No. 1 ignition relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 ignition relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 1 ignition relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - No. 1 ignition relay terminal 1 Always Below 1 Ω
F43-20 (IG1D) or No. 1 ignition relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 2 IGNITION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT NO. 2 IGNITION RELAY
a.

Remove the No. 2 ignition relay.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))

NG

REPLACE NO. 2 IGNITION RELAY

14.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))
a.

Remove the No. 2 ignition relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377753C01
0.24,0.229 0.615,0.469 0.375,0.24 12 false *A 4,0.281 4.375,0.521 0.375,0.24 12 false *B 4.219,0.854 4.594,1.094 0.375,0.24 10 false *1 0.604,0.51 0.979,0.75 0.375,0.24 10 false *1 1.563,0.344 1.938,0.583 0.375,0.24 10 false *2 4.802,0.417 5.177,0.656 0.375,0.24 10 false *2
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 2 Ignition Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 ignition relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (NO. 2 IGNITION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (NO. 2 IGNITION RELAY - BODY GROUND)
a.

Remove the No. 2 ignition relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 2 ignition relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 2 ignition relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - No. 2 ignition relay terminal 2 Always Below 1 Ω
F43-20 (IG1D) or No. 2 ignition relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the certification ECU (smart key ECU assembly) connector.

E374147C26
2.417,0.417 2.917,0.667 0.5,0.25 2.156,2.313 2.521,1.49 true 0.188,0.302 0.5,0.5 0.313,0.198 10 false *a 2.531,0.469 3.375,0.667 0.844,0.198 10 false F43 1.969,2.365 2.385,2.583 0.417,0.219 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage while checking the Data List on the GTS.

Standard Voltage:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)