If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
When the smart key cancel function has been canceled on the customization menu, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
*1: for CVT
*2: for Manual Transaxle
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG Relay Monitor(Inside) ·
IG Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor |
- |
for TMMIN Made
for TMT Made
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution.
Inspect the fuses of circuits related to this system before performing the following procedure.
After completing repairs, confirm that the problem does not occur.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press the lock or unlock switch of the electrical key transmitter sub-assembly and check the transmitter LED illuminates.
Transmitter LED illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | Yes or No | Yes: Transmitter battery depleted
No: Transmitter battery not depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
"NO" is displayed in the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.*1
With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.
*1: for CVT
*2: for Manual Transaxle
The power source mode changes.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the transmitter battery from the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.
*1: for CVT
*2: for Manual Transaxle
If the power source mode changes, the cabin verification is malfunctioning.
The power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode does not change | A |
| The power source mode changes | B |
A
B
Using the GTS, confirm the output of DTCs for all systems.
No DTCs are output.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Result | Proceed to |
|---|---|
| OK (for TMMIN Made) | A |
| OK (for TMT Made) | B |
| NG | C |
A
B
C
Remove the No. 1 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the F76 No. 1 ignition relay connector.
Disconnect the F77 No. 2 ignition relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - F76-1 | Always | Below 1 Ω |
| F76-2 - Body ground | Always | Below 1 Ω |
| F43-20 (IG1D) or F76-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay.
| *a | Front view of harness connector
(to No. 1 Ignition Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F76-5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the F77 No. 2 ignition relay connector.
Disconnect the F76 No. 1 ignition relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - F77-2 | Always | Below 1 Ω |
| F77-1 - Body ground | Always | Below 1 Ω |
| F43-20 (IG1D) or F77-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay.
| *a | Front view of wire harness connector
(to No. 2 Ignition Relay) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F77-3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-1 - 2L-3 | Battery voltage not applied to terminals 2F-2 and 2J-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 2F-2 and 2J-7 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the 2F and 2J driver side junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-21 (ACCD) - 2F-2 | Always | Below 1 Ω |
| 2J-7 - Body ground | Always | Below 1 Ω |
| F43-21 (ACCD) or 2F-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 certification ECU (smart key ECU assembly) connector.
Connect the 2F and 2J driver side junction block assembly connectors.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
Measure the voltage while checking the Data List on the GTS.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| F43-21 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (IG) | 8.5 V or higher | |
| Engine switch on (ACC) | 8.5 V or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the engine switch.
for 1NR-FE: Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 2NR-FE: Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
Inspect the engine switch.
for 1NR-FE: Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for LHD)>INSPECTION
for 2NR-FE: Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for LHD)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NR-FE) | B |
| NG (for 2NR-FE) | C |
A
B
C
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the F13 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-18 (SSW1) - F13-5 (SS1) | Always | Below 1 Ω |
| F43-16 (SSW2) - F13-1 (SS2) | Always | Below 1 Ω |
| F43-24 (AGND) - F13-6 (AGND) | Always | Below 1 Ω |
| F43-18 (SSW1) or F13-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F43-16 (SSW2) or F13-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F43-24 (AGND) or F13-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 1 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 ignition relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 1 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 ignition relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - No. 1 ignition relay terminal 1 | Always | Below 1 Ω |
| F43-20 (IG1D) or No. 1 ignition relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 2 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 2 ignition relay terminal 3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 2 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 2 ignition relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - No. 2 ignition relay terminal 2 | Always | Below 1 Ω |
| F43-20 (IG1D) or No. 2 ignition relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6A-1 - 6L-5 | Battery voltage not applied to terminals 6F-2 and 6J-8 | 10 kΩ or higher |
| Battery voltage applied to terminals 6F-2 and 6J-8 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the 6F and 6J driver side block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-21 (ACCD) - 6F-2 | Always | Below 1 Ω |
| 6J-8 - Body ground | Always | Below 1 Ω |
| F43-21 (ACCD) or 6F-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 certification ECU (smart key ECU assembly) connector.
Connect the 6F and 6J driver side junction block assembly connectors.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
| Tester Display |
|---|
| Power Supply Condition |
Measure the voltage while checking the Data List on the GTS.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| F43-21 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (IG) | 8.5 V or higher | |
| Engine switch on (ACC) | 8.5 V or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the engine switch.
for 1NR-FE (for LHD): Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 2NR-FE (for LHD): Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 1NR-FE (for RHD): Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
for 2NR-FE (for RHD): Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
Inspect the engine switch.
for 1NR-FE (for LHD): Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for LHD)>INSPECTION
for 2NR-FE (for LHD): Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for LHD)>INSPECTION
for 1NR-FE (for RHD): Click hereEngine / Hybrid System>1NR-FE STARTING>ENGINE SWITCH(for RHD)>INSPECTION
for 2NR-FE (for RHD): Click hereEngine / Hybrid System>2NR-FE STARTING>ENGINE SWITCH(for RHD)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NR-FE LHD) | B |
| NG (for 2NR-FE LHD) | C |
| NG (for 1NR-FE RHD) | D |
| NG (for 2NR-FE RHD) | E |
A
B
C
D
E
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the F13 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-18 (SSW1) - F13-5 (SS1) | Always | Below 1 Ω |
| F43-16 (SSW2) - F13-1 (SS2) | Always | Below 1 Ω |
| F43-24 (AGND) - F13-6 (AGND) | Always | Below 1 Ω |
| F43-18 (SSW1) or F13-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F43-16 (SSW2) or F13-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F43-24 (AGND) or F13-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery.
Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *a | Lead Wire |
Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
| *a | GND |
Measure the voltage of the transmitter battery.
When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.
Perform the measurement when the key is at room temperature.
The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Transmitter battery positive (+) - Transmitter battery negative (-) | Engine switch off, all doors closed and trigger switch pressed | 2.3 to 3.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT