Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment  


DESCRIPTION

If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment)*1 or electrical key antenna (luggage compartment)*2), a luggage door opening switch assembly".

*1: for TMMIN Made

*2: for TMT Made


WIRING DIAGRAM

for TMMIN Made


B348672E02
2.208,0.781 2.708,0.948 0.5,0.167 10 false ANTE8 1.146,1.552 1.344,1.729 0.198,0.177 10 false L4 2.708,0.667 2.854,0.854 0.146,0.188 10 false 1 2.708,1.104 2.854,1.292 0.146,0.188 10 false 3 5.771,0.771 6.271,0.938 0.5,0.167 10 false CLG8 5.771,1.198 6.271,1.365 0.5,0.167 10 false CG8B 5.771,1.854 6.271,2.021 0.5,0.167 10 false E 5.781,2.563 6.281,2.729 0.5,0.167 10 false TSW5 5.781,2.99 6.281,3.156 0.5,0.167 10 false RDA3 5.781,3.427 6.281,3.594 0.5,0.167 10 false PRG3 5.438,0.771 5.708,0.948 0.271,0.177 10 false F44 5.438,1.208 5.708,1.385 0.271,0.177 10 false F44 5.438,2.99 5.708,3.167 0.271,0.177 10 false F44 5.438,3.417 5.708,3.594 0.271,0.177 10 false F44 5.438,2.552 5.708,2.729 0.271,0.177 10 false F43 5.438,1.854 5.708,2.031 0.271,0.177 10 false F43 1.156,1.719 3.385,2.073 2.229,0.354 10 false No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment) 1.542,2.458 1.688,2.646 0.146,0.188 10 false 1 2.583,2.458 2.729,2.646 0.146,0.188 10 false 2 1.427,3.073 2.885,3.417 1.458,0.344 10 false Luggage Door Opening Switch Assembly 1.438,2.917 1.635,3.094 0.198,0.177 10 false L1 5.51,0.573 5.656,0.76 0.146,0.188 10 false 8 5.49,1.021 5.708,1.198 0.219,0.177 10 false 24 5.469,1.656 5.688,1.833 0.219,0.177 10 false 10 5.469,2.365 5.688,2.542 0.219,0.177 10 false 14 5.469,2.802 5.688,2.979 0.219,0.177 10 false 13 5.469,3.24 5.688,3.417 0.219,0.177 10 false 36 5.406,3.896 6.958,4.271 1.552,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.198,6.688 1.344,6.875 0.146,0.188 10 false 2 2.865,6.146 3.01,6.333 0.146,0.188 10 false 3 2.865,6.688 3.01,6.875 0.146,0.188 10 false 1 2.625,6.146 2.823,6.323 0.198,0.177 10 false D+ 2.448,6.698 2.813,6.875 0.365,0.177 10 false ACT+ 1.365,6.688 1.729,6.865 0.365,0.177 10 false ACT- 1.26,7.438 3.01,7.792 1.75,0.354 10 false Luggage Compartment Door Lock Assembly 1.271,7.281 1.469,7.458 0.198,0.177 10 false L5 4.156,6.229 4.354,6.406 0.198,0.177 10 false 2N 4.156,6.792 4.354,6.969 0.198,0.177 10 false 2O 4.208,6.042 4.354,6.229 0.146,0.188 10 false 3 4.208,6.583 4.354,6.771 0.146,0.188 10 false 1 5.438,5.01 5.708,5.188 0.271,0.177 10 false F52 5.438,5.448 5.708,5.625 0.271,0.177 10 false F52 5.448,6.229 5.688,6.417 0.24,0.188 10 false MB 5.469,6.792 5.708,6.979 0.24,0.188 10 false MB 5.792,5.031 6.292,5.198 0.5,0.167 10 false PRG 5.792,5.458 6.292,5.625 0.5,0.167 10 false RDA 5.781,6.24 6.281,6.406 0.5,0.167 10 false LGCY 5.792,6.792 6.292,6.958 0.5,0.167 10 false TR+ 4.313,7.323 5.563,7.646 1.25,0.323 10 false Driver Side Junction Block Assembly 5.667,7.51 6.677,7.698 1.01,0.188 10 false Body Computer 5.5,4.823 5.719,5 0.219,0.177 10 false 9 5.469,5.26 5.688,5.438 0.219,0.177 10 false 16 5.479,6.021 5.698,6.198 0.219,0.177 10 false 21 5.521,6.594 5.74,6.771 0.219,0.177 10 false 4 2.271,1.208 2.771,1.375 0.5,0.167 10 false CLGB


for TMT Made


B348672E05
2.208,0.781 2.708,0.948 0.5,0.167 10 false ANTE7 1.167,1.521 1.531,1.708 0.365,0.188 10 false F152 2.708,0.667 2.854,0.854 0.146,0.188 10 false 2 2.708,1.104 2.854,1.292 0.146,0.188 10 false 1 5.771,0.771 6.271,0.938 0.5,0.167 10 false CLG7 5.771,1.198 6.271,1.365 0.5,0.167 10 false CG7B 5.771,1.854 6.271,2.021 0.5,0.167 10 false E 5.781,2.563 6.281,2.729 0.5,0.167 10 false TSW5 5.781,2.99 6.281,3.156 0.5,0.167 10 false RDA3 5.781,3.427 6.281,3.594 0.5,0.167 10 false PRG3 5.438,0.771 5.708,0.948 0.271,0.177 10 false F44 5.438,1.208 5.708,1.385 0.271,0.177 10 false F44 5.438,2.99 5.708,3.167 0.271,0.177 10 false F44 5.438,3.417 5.708,3.594 0.271,0.177 10 false F44 5.438,2.552 5.708,2.729 0.271,0.177 10 false F43 5.438,1.854 5.708,2.031 0.271,0.177 10 false F43 1.167,1.719 3.156,2.135 1.99,0.417 10 false Electrical Key Antenna (Outside Luggage Compartment) 1.542,2.458 1.688,2.646 0.146,0.188 10 false 1 2.583,2.458 2.729,2.646 0.146,0.188 10 false 2 1.427,3.073 2.885,3.417 1.458,0.344 10 false Luggage Door Opening Switch Assembly 1.438,2.917 1.635,3.094 0.198,0.177 10 false L8 5.51,0.573 5.656,0.76 0.146,0.188 10 false 28 5.49,1.021 5.708,1.198 0.219,0.177 10 false 29 5.469,1.656 5.688,1.833 0.219,0.177 10 false 10 5.469,2.365 5.688,2.542 0.219,0.177 10 false 14 5.469,2.802 5.688,2.979 0.219,0.177 10 false 13 5.469,3.24 5.688,3.417 0.219,0.177 10 false 36 5.406,3.896 6.958,4.271 1.552,0.375 10 false Certification ECU (Smart Key ECU Assembly) 1.198,6.688 1.344,6.875 0.146,0.188 10 false 2 2.865,6.146 3.01,6.333 0.146,0.188 10 false 3 2.865,6.688 3.01,6.875 0.146,0.188 10 false 1 2.625,6.146 2.823,6.323 0.198,0.177 10 false D+ 2.448,6.698 2.813,6.875 0.365,0.177 10 false ACT+ 1.365,6.688 1.729,6.865 0.365,0.177 10 false ACT- 1.26,7.438 3.01,7.792 1.75,0.354 10 false Luggage Compartment Door Lock Assembly 1.271,7.281 1.469,7.458 0.198,0.177 10 false L5 4.156,6.229 4.354,6.406 0.198,0.177 10 false 6N 4.156,6.792 4.354,6.969 0.198,0.177 10 false 6J 4.208,6.042 4.354,6.229 0.146,0.188 10 false 1 4.208,6.583 4.354,6.771 0.146,0.188 10 false 2 5.438,5.01 5.708,5.188 0.271,0.177 10 false F52 5.438,5.448 5.708,5.625 0.271,0.177 10 false F52 5.448,6.229 5.688,6.417 0.24,0.188 10 false MB 5.469,6.792 5.708,6.979 0.24,0.188 10 false MB 5.792,5.031 6.292,5.198 0.5,0.167 10 false PRG 5.792,5.458 6.292,5.625 0.5,0.167 10 false RDA 5.781,6.24 6.281,6.406 0.5,0.167 10 false LGCY 5.792,6.792 6.292,6.958 0.5,0.167 10 false TR+ 4.313,7.323 5.563,7.688 1.25,0.365 10 false Driver Side Junction Block Assembly 5.667,7.552 6.677,7.74 1.01,0.188 10 false Body Computer 5.5,4.823 5.719,5 0.219,0.177 10 false 9 5.469,5.26 5.688,5.438 0.219,0.177 10 false 16 5.479,6.021 5.698,6.198 0.219,0.177 10 false 21 5.521,6.594 5.74,6.771 0.219,0.177 10 false 4 2.271,1.208 2.771,1.375 0.5,0.167 10 false CLGB


CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (TRUNK OPEN MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Trunk Open Mode Luggage compartment door open mode ON or OFF Customization status displayed -
Body Electrical > Entry&Start > Data List
Tester Display
Trunk Open Mode
50003 125 3

Result:
Result Proceed to
Entry luggage compartment door open mode is ON A
Entry luggage compartment door open mode is OFF B



A

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)

B

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Luggage door opening switch assembly ON or OFF ON: Luggage door opening switch assembly pushed
OFF: Luggage door opening switch assembly not pushed
·

Displays whether the luggage door opening switch assembly is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

On the GTS screen, the display changes between ON and OFF according to the chart above.



Result:
Result Proceed to
OK (for TMMIN Made) A
OK (for TMT Made) B
NG C



A

3.CHECK WAVE ENVIRONMENT

B

14.CHECK WAVE ENVIRONMENT

C

25.INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY
3.CHECK WAVE ENVIRONMENT
a.
B342601C05
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly near No. 3 indoor electrical key antenna assembly (luggage compartment), and perform an entry luggage compartment door open function check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.


HINT:
·

When pressing the luggage door opening switch assembly, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.

·

When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key antenna assembly (luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




Result:
Result Proceed to
Entry functions do not operate normally A
Entry functions operate normally B



A

4.CHECK KEY DIAGNOSTIC MODE

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK KEY DIAGNOSTIC MODE

b.
B342601C06
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a 0.7 to 1.0 m (2.30 to 3.28 ft.)


Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

i.

When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.

·

If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless door lock buzzer do not sounds A
Wireless door lock buzzer sounds B



A

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-8 (CLG8) - L4-1 (ANTE8) Always Below 1 Ω
F44-24 (CG8B) - L4-3 (CLGB) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-8 (CLG8) or L4-1 (ANTE8) - Body ground Always 10 kΩ or higher
F44-24 (CG8B) or L4-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)
a.

Connect the F43 or F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.


c.

Using an oscilloscope, check the waveform.

B345002C03
0.844,1.198 1.292,1.448 0.448,0.25 4.208,2.281 4.438,1.458 true 1.49,2.219 1.719,1.396 true 2.073,2.229 1.854,1.406 true 0.99,1.24 1.448,1.438 0.458,0.198 10 false L4 1.135,0.688 1.448,0.885 0.313,0.198 10 false *a 3.531,0.469 3.844,0.667 0.313,0.198 10 false *b 3.479,1.302 3.938,1.5 0.458,0.198 10 false GND 4.115,2.323 4.427,2.521 0.313,0.198 10 false *c 1.313,2.271 1.75,2.469 0.438,0.198 10 false CLGB 1.906,2.271 2.458,2.469 0.552,0.198 10 false ANTE8
*a Component with harness connected
(No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment))
*b Waveform 1
*c luggage door opening switch assembly ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
L4-1 (ANTE8) - L4-3 (CLGB) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Press the luggage door opening switch assembly


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

7.CHECK ENTRY OPERATION

NG

REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)

7.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) before performing the inspection.


Result:
Result Proceed to
Entry unlock functions do not operate normally A
Entry unlock functions operate normally B




A

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECT CONNECTORS PROPERLY)

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform the registration procedures.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK ENTRY OPERATION
9.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

Result:
Result Proceed to
Entry functions do not operate normally A
Entry functions operate normally B




A

10.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

B

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

10.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
a.

Remove the luggage compartment door lock assembly.

Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK(for TMMIN Made)>REMOVAL


b.

Inspect the luggage compartment door lock assembly.

Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK(for TMMIN Made)>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)
a.

Luggage compartment door lock motor:

i.

Disconnect the 2O driver side junction block assembly connector.


ii.

Disconnect the L5 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2O-1 - L5-1 (ACT+) Always Below 1 Ω
L5-2 (ACT-) - Body ground Always Below 1 Ω
2O-1 or L5-1 (ACT+) - Body ground Always 10 kΩ or higher




b.

Luggage door courtesy light switch:

i.

Disconnect the 2N driver side junction block assembly connector.


ii.

Disconnect the L5 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-3 - L5-3 (D+) Always Below 1 Ω
L5-2 (ACT-) - Body ground Always Below 1 Ω
2N-3 or L5-3 (D+) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

12.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Temporarily replace the driver side junction block assembly with a new or known good one.

for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL

for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK ENTRY OPERATION
13.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Luggage compartment door entry unlock functions operate normally.



Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

END (DRIVER SIDE JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

B

C

14.CHECK WAVE ENVIRONMENT
a.
B342601C05
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly near electrical key antenna (outside luggage compartment), and perform an entry luggage compartment door open function check.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.


HINT:
·

When pressing the luggage door opening switch assembly, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.

·

When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




Result:
Result Proceed to
Entry functions do not operate normally A
Entry functions operate normally B



A

15.CHECK KEY DIAGNOSTIC MODE

B

AFFECTED BY WAVE INTERFERENCE

15.CHECK KEY DIAGNOSTIC MODE

b.
B342601C06
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a 0.7 to 1.0 m (2.30 to 3.28 ft.)


Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

i.

When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.

·

If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F152 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-28 (CLG7) - F152-2 (ANTE7) Always Below 1 Ω
F44-29 (CG7B) - F152-1 (CLGB) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-28 (CLG7) or F152-2 (ANTE7) - Body ground Always 10 kΩ or higher
F44-29 (CG7B) or F152-1 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)
a.

Connect the F43 or F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the F152 electrical key antenna (outside luggage compartment) connector.


c.

Using an oscilloscope, check the waveform.

E374150C04
2.49,0.5 3,0.75 0.51,0.25 4.573,0.5 5.083,0.75 0.51,0.25 1.875,2.542 2.229,1.552 true 2.917,4.458 3.302,3.76 true 5.396,2.646 4.896,1.635 true 4.542,2.656 4.833,1.635 true 0.531,0.552 0.875,0.771 0.344,0.219 10 false *a 2.615,2.979 3.052,3.271 0.438,0.292 10 false *b 2.76,4.458 3.115,4.646 0.354,0.188 10 false *c 2.615,0.552 2.958,0.771 0.344,0.219 10 false F43 4.698,0.542 5.042,0.76 0.344,0.219 10 false F44 2.375,3.635 2.792,3.844 0.417,0.208 10 false GND 1.792,2.573 2.135,2.792 0.344,0.219 10 false E 5.26,2.698 6.094,3.135 0.833,0.438 10 false CLG7 4.354,2.698 5.188,3.135 0.833,0.438 10 false CG7B
*a Component with harness connected
Certification ECU (Smart Key ECU Assembly)
*b Waveform 1
*c luggage door opening switch assembly ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-28 (CLG7) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Press the luggage door opening switch assembly


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-29 (CG7B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Press the luggage door opening switch assembly


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

18.CHECK ENTRY OPERATION

NG

18.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) before performing the inspection.


Result:
Result Proceed to
Entry unlock functions do not operate normally A
Entry unlock functions operate normally B




A

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECT CONNECTORS PROPERLY)

19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform the registration procedures.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.CHECK ENTRY OPERATION
20.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

Result:
Result Proceed to
Entry functions do not operate normally A
Entry functions operate normally B




A

21.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

B

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

21.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
a.

Remove the luggage compartment door lock assembly.

Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK(for TMT Made)>REMOVAL


b.

Inspect the luggage compartment door lock assembly.

Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK(for TMT Made)>INSPECTION


Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)

NG

REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY

22.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY)
a.

Luggage compartment door lock motor:

i.

Disconnect the 6J driver side junction block assembly connector.


ii.

Disconnect the L5 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6J-2 - L5-1 (ACT+) Always Below 1 Ω
L5-2 (ACT-) - Body ground Always Below 1 Ω
6J-2 or L5-1 (ACT+) - Body ground Always 10 kΩ or higher




b.

Luggage door courtesy light switch:

i.

Disconnect the 6N driver side junction block assembly connector.


ii.

Disconnect the L5 luggage compartment door lock assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6N-1 - L5-3 (D+) Always Below 1 Ω
L5-2 (ACT-) - Body ground Always Below 1 Ω
6N-1 or L5-3 (D+) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

23.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Temporarily replace the driver side junction block assembly with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.CHECK ENTRY OPERATION
24.CHECK ENTRY OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Luggage compartment door entry unlock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (DRIVER SIDE JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

25.INSPECT LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY


Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - LUGGAGE DOOR OPENING SWITCH ASSEMBLY)

B

REPLACE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY

C

REPLACE LUGGAGE COMPARTMENT DOOR OPENING SWITCH ASSEMBLY

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - LUGGAGE DOOR OPENING SWITCH ASSEMBLY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L1*1 or L8*2 luggage door opening switch assembly connector.

*1: for TMMIN Made

*2: for TMT Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMIN Made
Tester Connection Condition Specified Condition
F43-14 (TSW5) - L1-2 Always Below 1 Ω
L1-1 - Body ground Always Below 1 Ω
F43-14 (TSW5) or L1-2 - Body ground Always 10 kΩ or higher

for TMT Made
Tester Connection Condition Specified Condition
F43-14 (TSW5) - L8-2 Always Below 1 Ω
L8-1 - Body ground Always Below 1 Ω
F43-14 (TSW5) or L8-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR