If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the unlock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).
The entry and start system (for Entry Function) uses the multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch assembly (unlock switch) | ON or OFF | ON: Back door opener switch assembly (unlock switch) pushed
OFF: Back door opener switch assembly (unlock switch) not pushed |
·
Displays whether the back door opener switch assembly (unlock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door unlock function does not operate. |
| Tester Display |
|---|
| Tr/B-Door Unlock SW |
The GTS display changes correctly in response to the operation of the back door opener switch assembly.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the R8 back door opener switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-14 (TSW5) - R8-3 (UL) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| R8-2 (E) - Body ground | Always | Below 1 Ω |
| F43-14 (TSW5) or R8-3 (UL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL
Inspect the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the entry back door unlock operation.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and back door opener switch assembly before performing the inspection.
Entry back door unlock operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the body computer with a new or known good one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the entry back door unlock operation.
Entry back door unlock operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG