Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0090060 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87150B 1.INSTALL HEATER RADIATOR ASSEMBLY

a.

Install the heater radiator assembly.


b.
I109980

Engage the claw and install the plate cover.


c.

Install the 2 claws.


d.

for RHD:

i.
I109982

Engage the 2 claws and 3 guides and install the heater cover.


ii.

Install the 5 screws.



Hide 88501 4.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

HINT:

If a new No. 1 cooler evaporator sub-assembly is installed, add compressor oil to the No. 1 cooler evaporator sub-assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz.)


Compressor oil:

ND-OIL 8 or equivalent.


a.
I109841

Install the No. 1 cooler evaporator sub-assembly with the No. 1 cooler thermistor.


b.

for LHD:

i.
I109839

Engage the 7 claws and install the lower heater case.



c.

for RHD:

i.
I109679

Engage the 8 claws and install the lower heater case.



d.
I113933

Install the 6 screws.


e.
I109837

Engage the clamp.


Hide 88515 5.INSTALL NO. 1 EXPANSION VALVE

a.

Apply sufficient compressor oil to 2 new O-rings and fitting surfaces of a No. 1 expansion valve.

Compressor oil:

ND-OIL 8 or equivalent



b.
I109691C01
2,0.656 2.417,0.24 true 2.479,0.146 2.792,0.344 0.313,0.198 10 true *1
*1 No. 1 Cooler Evaporator Sub-assembly


Install the 2 O-rings onto the No. 1 cooler evaporator sub-assembly.


c.
I109692

Using a 4 mm hexagon wrench, install the No. 1 expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 82210K 6.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)

a.

for LHD:

i.
I110020

Engage the 5 guides and install the air conditioning harness assembly.



b.

for RHD:

i.
I110069

Engage the 5 guides and install the air conditioning harness assembly.



Hide 88897U 7.INSTALL ASPIRATOR PIPE (for Automatic Air Conditioning System)

a.
I114008

Engage the 2 claws and install the aspirator pipe.


Hide 88669E 8.INSTALL AIR HOSE (for Automatic Air Conditioning System)

a.
I114007

Install the air hose.


Hide 87106H 9.INSTALL AIR MIX DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
I114009C01
0.656,0.542 0.521,0.313 true 0.448,0.125 0.646,0.323 0.198,0.198 10 true *a
*a Reference position


Align the reference position, and then install the air mix damper servo sub-assembly with the 3 screws.


b.

Connect the connector.


Hide 87106J 10.INSTALL MODE DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
I114010C01
2.146,0.354 2.094,0.573 true 2.115,0.156 2.313,0.354 0.198,0.198 10 true *a
*a Reference position


Align the reference position, and then install the mode damper servo sub-assembly with the 3 screws.


b.

Connect the connector.


Hide 87106N 11.INSTALL RECIRCULATION DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.
I114011C01
1.875,1.458 1.708,1.833 1.708,1.833 1.958,1.594 true 1.594,1.813 1.792,2.021 0.198,0.208 10 true *a
*a Reference position


Align the reference position, and then install the recirculation damper servo sub-assembly with the 3 screws.


b.

Connect the connector.


Hide 87106N 12.INSTALL RECIRCULATION DAMPER SERVO SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 88539 13.INSTALL NO. 1 COOLER UNIT DRAIN HOSE

a.
I109836

Install the No. 1 cooler unit drain hose.


Hide 87139D 14.INSTALL AIR REFINER ELEMENT

a.
I109638

Install the air refiner element.

NOTICE:

Install the air refiner element with its UP marks oriented in the correct direction.



Hide 88548B 15.INSTALL AIR FILTER CASE

a.
I110065

Engage the claw and guide to install the air filter case.

NOTICE:

Install the air filter case with its UP mark oriented in the correct direction.



Hide 87103B 16.INSTALL BLOWER MOTOR WITH FAN SUB-ASSEMBLY

a.
I109833

Install the blower motor with fan sub-assembly with the 3 screws.