84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Visually check for defects with the spiral cable sub-assembly removed from the vehicle.
The defects are as follows:
Scratches on the spiral cable sub-assembly
Small cracks on the spiral cable sub-assembly
Dents on the spiral cable sub-assembly
Chips on the spiral cable sub-assembly
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
| *a | Component without harness connected (Spiral Cable Sub-assembly) |
|
Interlock |
Check the resistance.
When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (CCS) - C-3 | Always | 3 Ω or less |
| E-2 (ECC) - C-4 | ||
| E-2 (ECC) - B-7 | ||
| E-3 (EAU) - B-8 | ||
| E-5 (AU2) - B-10 | ||
| E-6 (AU1) - B-11 | ||
| E-7 (SDN) - B-12 | ||
| E-9 (HO) - B-1 | ||
| E-10 (+DP) - B-2 | ||
| E-11 (+DP2) - B-3 | ||
| E-13 (IL+2) - B-5 | ||
| E-14 (SUP) - B-6 | ||
| D-1 (D+) - A-2 | Below 1 Ω | |
| D-2 (D-) - A-1 |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (CCS) - C-3 | Always | 3 Ω or less |
| E-2 (ECC) - C-4 | ||
| E-2 (ECC) - B-7 | ||
| E-3 (EAU) - B-8 | ||
| E-5 (AU2) - B-10 | ||
| E-6 (AU1) - B-11 | ||
| E-7 (SDN) - B-12 | ||
| E-9 (HO) - B-1 | ||
| E-10 (+DP) - B-2 | ||
| E-11 (+DP2) - B-3 | ||
| E-13 (IL+2) - B-5 | ||
| E-14 (SUP) - B-6 | ||
| D-1 (D+) - A-2 | Below 1 Ω | |
| D-2 (D-) - A-1 |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-1 (CCS) - C-3 | Always | 3 Ω or less |
| E-2 (ECC) - C-4 | ||
| E-3 (EAU) - B-8 | ||
| E-5 (AU2) - B-10 | ||
| E-6 (AU1) - B-11 | ||
| E-7 (SDN) - B-12 | ||
| E-9 (HO) - B-1 | ||
| E-10 (+DP) - B-2 | ||
| E-11 (+DP2) - B-3 | ||
| E-13 (IL+2) - B-5 | ||
| E-14 (SUP) - B-6 | ||
| D-1 (D+) - A-2 | Below 1 Ω | |
| D-2 (D-) - A-1 |
If the result is not as specified, replace the spiral cable sub-assembly.