Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2018.01
RM30M0E _59 Vehicle Exterior _017126 LIGHTING (EXT) _0090942 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Turn Signal Switch Circuit  


DESCRIPTION

The combination meter assembly receives the headlight dimmer switch assembly (turn signal switch) information and controls the turn signal lights.

WIRING DIAGRAM

E376552E01
0.115,0.094 1.583,0.333 1.469,0.24 12 false for LHD: 5.646,4.021 6.104,4.219 0.458,0.198 10 false F39 5.625,4.198 6.813,4.688 1.188,0.49 10 false Combination Meter Assembly 5.75,2.031 6.208,2.229 0.458,0.198 10 false EL 5.74,1.531 6.198,1.729 0.458,0.198 10 false ER 5.469,1.917 5.927,2.115 0.458,0.198 10 false 10 5.531,1.406 5.99,1.604 0.458,0.198 10 false 9 3.323,0.792 3.781,0.99 0.458,0.198 10 false EL 3.302,1.375 3.76,1.573 0.458,0.198 10 false TR 0.677,4.073 1.135,4.271 0.458,0.198 10 false F17 3.615,0.802 4.073,1 0.458,0.198 10 false 15 3.615,1.375 4.073,1.573 0.458,0.198 10 false 12 3.625,1.927 4.083,2.125 0.458,0.198 10 false 11 3.104,2.542 3.563,2.74 0.458,0.198 10 false TL 2.719,2.531 3.177,2.729 0.458,0.198 10 false TR 2.354,2.531 2.813,2.729 0.458,0.198 10 false E 0.677,2.854 1.427,3.427 0.75,0.573 10 false Turn Signal Switch 1.948,3.188 2.406,3.385 0.458,0.198 10 false N 1.896,3.542 2.354,3.74 0.458,0.198 10 false LH 1.885,2.813 2.344,3.01 0.458,0.198 10 false RH 0.677,4.24 3.531,4.615 2.854,0.375 10 false Headlight Dimmer Switch Assembly 3.333,1.938 3.792,2.135 0.458,0.198 10 false TL

E376552E02
0.115,0.094 1.583,0.333 1.469,0.24 12 false for RHD: 5.646,4.021 6.104,4.219 0.458,0.198 10 false F39 5.625,4.198 6.813,4.688 1.188,0.49 10 false Combination Meter Assembly 5.75,2.031 6.208,2.229 0.458,0.198 10 false EL 5.74,1.531 6.198,1.729 0.458,0.198 10 false ER 5.469,1.917 5.927,2.115 0.458,0.198 10 false 10 5.531,1.406 5.99,1.604 0.458,0.198 10 false 9 3.323,0.792 3.781,0.99 0.458,0.198 10 false EL 3.302,1.375 3.76,1.573 0.458,0.198 10 false TR 3.344,1.917 3.802,2.115 0.458,0.198 10 false TL 3.615,0.802 4.073,1 0.458,0.198 10 false 16 3.625,1.375 4.083,1.573 0.458,0.198 10 false 20 3.625,1.927 4.083,2.125 0.458,0.198 10 false 19 3.104,2.542 3.563,2.74 0.458,0.198 10 false TL 2.719,2.531 3.177,2.729 0.458,0.198 10 false TR 2.354,2.531 2.813,2.729 0.458,0.198 10 false E 0.677,2.854 1.427,3.427 0.75,0.573 10 false Turn Signal Switch 1.948,3.188 2.406,3.385 0.458,0.198 10 false N 1.896,3.542 2.354,3.74 0.458,0.198 10 false LH 1.885,2.813 2.344,3.01 0.458,0.198 10 false RH 0.698,4.229 3.552,4.604 2.854,0.375 10 false Headlight Dimmer Switch Assembly 0.708,4.063 1.167,4.26 0.458,0.198 10 false F17

PROCEDURE

1.READ VALUE USING GTS (TURN SIGNAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Turn signal switch (Right) signal ON or OFF ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off
-
Turn Signal Switch (Left) Turn signal switch (Left) signal ON or OFF ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off
-
Body Electrical > Combination Meter > Data List
Tester Display
Turn Signal Switch (Right)
Turn Signal Switch (Left)
50003 122 98,97
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL SWITCH)
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL SWITCH)
a.

Inspect the headlight dimmer switch assembly (turn signal switch).

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F17 headlight dimmer switch assembly connector.


b.

Disconnect the F39 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F17-12 (TR) - F39-9 (ER) Always Below 1 Ω
F17-11 (TL) - F39-10 (EL) Always Below 1 Ω
F17-15 (EL) - Body ground Always Below 1 Ω
F17-12 (TR) or F39-9 (ER) - Body ground Always 10 kΩ or higher
F17-11 (TL) or F39-10 (EL) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F17-20 (TR) - F39-9 (ER) Always Below 1 Ω
F17-19 (TL) - F39-10 (EL) Always Below 1 Ω
F17-16 (EL) - Body ground Always Below 1 Ω
F17-20 (TR) or F39-9 (ER) - Body ground Always 10 kΩ or higher
F17-19 (TL) or F39-10 (EL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR