Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086573 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1411  Room Temperature Sensor Circuit  


DESCRIPTION

The cooler (room temperature sensor) thermistor is installed in the instrument panel to detect the cabin temperature which is used to control the air conditioning system. The resistance of the cooler (room temperature sensor) thermistor changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler (room temperature sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (room temperature sensor) thermistor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1411 Room Temperature Sensor Circuit Open or short in cooler (room temperature sensor) thermistor circuit
·

Cooler (room temperature sensor) thermistor

·

Harness or connector between cooler (room temperature sensor) thermistor and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the cabin temperature is approximately -18.6°C (-1.48°F) or lower, DTC B1411 may be output even though the system is normal.


WIRING DIAGRAM

E236721E39
2.146,0.448 2.531,0.844 0.385,0.396 10 false 1 2.146,1.396 2.646,1.729 0.5,0.333 10 false 2 5.115,0.448 5.552,0.75 0.438,0.302 10 false 29 5.115,1.406 5.51,1.708 0.396,0.302 10 false 15 5.396,0.542 6.146,0.958 0.75,0.417 10 false TR 5.396,1.49 6.146,1.833 0.75,0.344 10 false SG-1 0.896,1.958 1.219,2.135 0.323,0.177 10 false F57 0.896,2.115 2.594,2.479 1.698,0.365 10 false Cooler (Room Temperature Sensor) Thermistor 5.052,1.885 5.333,2.063 0.281,0.177 10 false F3 5.052,2.052 6.635,2.521 1.583,0.469 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Room Temperature Sensor Cooler (room temperature sensor) thermistor Min.: -6.50°C (20.30°F)
Max.: 57.25°C (135.05°F)
Actual cabin temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Room Temperature Sensor
50003 121 1
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR
2.INSPECT COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR
a.

Remove the cooler (room temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>REMOVAL


b.

Inspect the cooler (room temperature sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR

3.CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMPERATURE SENSOR) THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F57 cooler (room temperature sensor) thermistor connector.


b.

Disconnect the F3 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-29 (TR) - F57-1 Always Below 1 Ω
F3-15 (SG-1) - F57-2 Always Below 1 Ω
F3-29 (TR) or F57-1 - Body ground Always 10 kΩ or higher
F3-15 (SG-1) or F57-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR