The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1497 | Communication Malfunction (Bus Ic) | Error or open in communication line | ·
Air conditioning harness assembly ·
Harness or connecter between air conditioning amplifier assembly and power source ·
Air mix damper servo sub-assembly ·
Mode damper servo sub-assembly ·
Recirculation damper servo sub-assembly ·
Air conditioning amplifier assembly ·
Air conditioning panel circuit |
Memorized
(10 seconds or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
Inspect the fuses for circuits related to this system before performing the following procedure.
DTCs B1497 and B14B2 may be output simultaneously.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | Air mix damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
for LHD
Operates between 183 and 257 pulses for RHD
Operates between 255 and 329 pulses |
| Air Outlet Servo Pulse (D) | Mode damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
for LHD
Operates between 252 and 316 pulses for RHD
Operates between 196 and 260 pulses |
| Air Inlet Damper Targ Pulse | Recirculation damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
for LHD
Operates between 255 and 270 pulses for RHD
Operates between 242 and 257 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
| Tester Display |
|---|
| Air Outlet Servo Pulse (D) |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
Arm of the damper servo motor selected in the Active Test operates smoothly.
According to the test result, proceed to the next step.
| Result | Proceed to |
|---|---|
| One of the damper servo motors is malfunctioning | A |
| All of the damper servo motors are malfunctioning | B |
A
B
According to the test, proceed to the next step.
| Result | Proceed to |
|---|---|
| Only the air mix damper servo sub-assembly is malfunctioning | A |
| Only the recirculation damper servo sub-assembly is malfunctioning | B |
| Only the mode damper servo sub-assembly is malfunctioning | C |
A
B
C
Replace the air mix damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air mix damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the air mix damper servo sub-assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-21 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Confirm whether of DTC B14B2 is output.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B14B2 is not output | A |
| DTC B14B2 is output | B |
A
B
Check whether DTC B14B2 procedure has been completed.
| Result | Proceed to |
|---|---|
| DTC B14B2 check procedure has not been completed | A |
| DTC B14B2 check procedure has been completed | B |
A
B
Replace the recirculation damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B
Replace the mode damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the mode damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the mode damper servo sub-assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1497 is not output | A |
| DTC B1497 is output | B |
A
B