Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086991 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

When the heater control and accessory assembly is operated, the heater relay will turn on to allow current to flow to the blower motor and then the motor will start rotating. Operating the heater control and accessory assembly switches the current flow between the blower resistor and body ground, thus, shifting the rotation speed of the blower motor with fan sub-assembly.

WIRING DIAGRAM

E376555E01
4.74,6.667 6.073,6.885 1.333,0.219 10 false Blower Switch 0.104,0.563 1.031,1.563 0.927,1 10 false from Ignition or Starter Switch Assembly*1 or IG1 Relay*2 1.385,0.906 3.219,1.104 1.833,0.198 10 false ECU-IG NO. 1 0.406,2.021 2.24,2.219 1.833,0.198 10 false from Battery 1.771,2.208 3.604,2.406 1.833,0.198 10 false HTR 2.781,2.385 4.615,2.583 1.833,0.198 10 false HTR 3.729,2.24 5.563,2.438 1.833,0.198 10 false F53 3.24,1.417 3.396,1.615 0.156,0.198 10 false 1 4.302,1.927 4.458,2.125 0.156,0.198 10 false 1 2.469,1.417 2.625,1.615 0.156,0.198 10 false 2 2.469,1.927 2.625,2.125 0.156,0.198 10 false 5 3.24,1.938 3.396,2.135 0.156,0.198 10 false 3 3.729,1.927 3.885,2.125 0.156,0.198 10 false 2 3.729,2.417 4.896,2.865 1.167,0.448 10 false Blower Motor with Fan Sub-assembly 5.594,2.448 6.781,2.792 1.188,0.344 10 false F124 5.594,2.635 7.156,3.26 1.563,0.625 10 false Air Conditioning Amplifier Assembly 6.031,1.542 7.156,1.792 1.125,0.25 10 false HR 6.031,2.042 7.156,2.292 1.125,0.25 10 false SBLW 5.792,1.438 6.125,1.708 0.333,0.271 10 false 20 5.792,1.927 6.125,2.198 0.333,0.271 10 false 26 3.885,7.188 5.073,7.531 1.188,0.344 10 false F5 3.885,7.344 6.802,7.635 2.917,0.292 10 false Heater Control and Accessory Assembly 0.635,6.75 1.823,7.094 1.188,0.344 10 false F55 0.635,6.917 1.823,7.26 1.188,0.344 10 false Blower Resistor 3.813,6.365 4.938,6.615 1.125,0.25 10 false E 5.146,4.365 6.271,4.615 1.125,0.25 10 false LO 4.719,4.365 5.844,4.615 1.125,0.25 10 false M1 4.292,4.365 5.417,4.615 1.125,0.25 10 false M2 3.948,4.375 5.073,4.625 1.125,0.25 10 false HI 4.115,4.615 5.24,4.865 1.125,0.25 10 false HI 4.458,4.604 5.583,4.854 1.125,0.25 10 false M2 4.854,4.615 5.979,4.865 1.125,0.25 10 false M1 5.24,4.604 6.365,4.854 1.125,0.25 10 false LO 5.656,4.615 6.781,4.865 1.125,0.25 10 false E 5.104,3.99 5.458,4.198 0.354,0.208 10 false 7*3 5.104,4.167 5.458,4.375 0.354,0.208 10 false 8*4 0.198,8.063 3.177,8.427 2.979,0.365 10 false *1: w/o Smart Entry & Start System 4.708,4.167 5.063,4.375 0.354,0.208 10 false 8*4 4.719,3.99 5.073,4.198 0.354,0.208 10 false 9*3 4.333,4.146 4.688,4.354 0.354,0.208 10 false 10 4.021,4.146 4.375,4.354 0.354,0.208 10 false 5 3.604,6.229 3.76,6.427 0.156,0.198 10 false 1 2.771,6.063 3.094,6.24 0.323,0.177 10 false 1*3 2.76,6.25 3.083,6.427 0.323,0.177 10 false 4*4 1.917,6.021 2.24,6.198 0.323,0.177 10 false 2*4 1.51,6.01 1.833,6.188 0.323,0.177 10 false 3*4 1.51,5.823 1.833,6 0.323,0.177 10 false 2*3 1.917,5.823 2.24,6 0.323,0.177 10 false 3*3 0.208,6.052 0.531,6.229 0.323,0.177 10 false 4*3 0.198,6.25 0.521,6.427 0.323,0.177 10 false 1*4 0.552,6.24 1.677,6.49 1.125,0.25 10 false HI 1.5,6.229 2.625,6.479 1.125,0.25 10 false M2 1.938,6.219 3.063,6.469 1.125,0.25 10 false M1 2.552,6.229 3.677,6.479 1.125,0.25 10 false E 0.177,8.438 3.156,8.802 2.979,0.365 10 false *2: w/ Smart Entry & Start System 2.677,8.063 5.656,8.427 2.979,0.365 10 false *3: for LHD 2.698,8.438 5.677,8.802 2.979,0.365 10 false *4: for RHD 6.083,4.823 6.354,5.042 0.271,0.219 10 false 0 6.083,5.042 6.354,5.26 0.271,0.219 10 false 1 5.99,5.25 6.49,5.5 0.5,0.25 10 false 1 - 2 6.083,5.49 6.354,5.708 0.271,0.219 10 false 2 5.99,5.698 6.49,5.917 0.5,0.219 10 false 2 - 3 6.083,5.917 6.354,6.135 0.271,0.219 10 false 3 5.99,6.146 6.313,6.323 0.323,0.177 10 false 3 - 4 6.094,6.365 6.344,6.563 0.25,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT HTR RELAY
a.

Remove the HTR relay from the No. 3 relay block.



Result:
Proceed to
OK
NG



OK

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE HTR RELAY

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Remove the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL


b.

Inspect the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT BLOWER RESISTOR

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

3.INSPECT BLOWER RESISTOR


Result:
Proceed to
OK
NG



OK

4.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

NG

4.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HTR RELAY - POWER SOURCE)

NG

5.CHECK HARNESS AND CONNECTOR (HTR RELAY - POWER SOURCE)
a.

Remove the HTR relay from the No. 3 relay block.


b.
E371818C01
0.115,0.167 0.427,0.323 0.313,0.156 10 false *1 1.625,0.354 1.938,0.51 0.313,0.156 10 false *a
*1 No. 3 Relay Block
*a HTR Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HTR RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HTR RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Remove the HTR relay from the No. 3 relay block.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - F53-2 Always Below 1 Ω
Relay terminal 3 or F53-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F55 blower resistor connector.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F55-4 (HI) - F53-1 Always Below 1 Ω
F55-1 (E) - Body ground Always Below 1 Ω
F55-4 (HI) or F53-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F55-1 (HI) - F53-1 Always Below 1 Ω
F55-4 (E) - Body ground Always Below 1 Ω
F55-1 (HI) or F53-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Disconnect the F53 blower motor with fan sub-assembly connector.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-1 - F5-5 (HI) Always Below 1 Ω
F53-1 or F5-5 (HI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)
a.

Disconnect the F5 heater control and accessory assembly connector.


b.

Disconnect the F55 blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F5-10 (M2) - F55-2 (M2) Always Below 1 Ω
F5-9 (M1) - F55-3 (M1) Always Below 1 Ω
F5-1 (E) - Body ground Always Below 1 Ω
F5-10 (M2) or F55-2 (M2) - Body ground Always 10 kΩ or higher
F5-9 (M1) or F55-3 (M1) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
F5-10 (M2) - F55-3 (M2) Always Below 1 Ω
F5-8 (M1) - F55-2 (M1) Always Below 1 Ω
F5-1 (E) - Body ground Always Below 1 Ω
F5-10 (M2) or F55-3 (M2) - Body ground Always 10 kΩ or higher
F5-8 (M1) or F55-2 (M1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HTR RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - HTR RELAY AND HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Remove the HTR relay from the No. 3 relay block.


b.

Disconnect the F124 air conditioning amplifier assembly connector.


c.

Disconnect the F5 heater control and accessory assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F124-20 (HR) - Relay terminal 1 Always Below 1 Ω
F124-26 (SBLW) - F5-7 (LO) Always Below 1 Ω
F124-20 (HR) or Relay terminal 1 - Body ground Always 10 kΩ or higher
F124-26 (SBLW) or F5-7 (LO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F124-20 (HR) - Relay terminal 1 Always Below 1 Ω
F124-26 (SBLW) - F5-8 (LO) Always Below 1 Ω
F124-20 (HR) or Relay terminal 1 - Body ground Always 10 kΩ or higher
F124-26 (SBLW) or F5-8 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR