Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0086434 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the front passenger side manual up/down function does not operate, a malfunction may be present in the front power window regulator motor assembly (front passenger side), power window regulator switch assembly (front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

E376610E13
1.031,0.625 1.344,0.823 0.313,0.198 10 false G9 1.031,0.771 2.948,1.219 1.917,0.448 10 false Front Power Window Regulator Motor Assembly RH 3.208,0.531 3.521,0.729 0.313,0.198 10 false 2 3.208,1.125 3.521,1.323 0.313,0.198 10 false 1 5.146,3.927 6.719,4.469 1.573,0.542 10 false Power Window Regulator Switch Assembly RH 5.146,3.771 5.656,4 0.51,0.229 10 false G10 0.427,3.823 0.938,4.052 0.51,0.229 10 false H8 0.427,3.979 1.99,4.531 1.563,0.552 10 false Power Window Regulator Master Switch Assembly 1.667,2.917 2.177,3.146 0.51,0.229 10 false U 1.667,3.385 2.177,3.615 0.51,0.229 10 false D 1.833,2.813 2.115,3.021 0.281,0.208 10 false 10 1.833,3.292 2.115,3.5 0.281,0.208 10 false 18 5.219,0.375 5.729,0.604 0.51,0.229 10 false U 5.219,1.271 5.729,1.5 0.51,0.229 10 false D 5.219,1.823 5.729,2.052 0.51,0.229 10 false B 5.219,2.896 5.729,3.125 0.51,0.229 10 false SU 5.219,3.365 5.729,3.594 0.51,0.229 10 false SD 5.031,0.302 5.542,0.531 0.51,0.229 10 false 7 5.042,1.188 5.552,1.417 0.51,0.229 10 false 1 5.031,1.75 5.344,1.948 0.313,0.198 10 false 2 5.021,2.833 5.333,3.031 0.313,0.198 10 false 3 5.031,3.302 5.344,3.5 0.313,0.198 10 false 4 2.698,1.979 3.333,2.24 0.635,0.26 10 false POWER 1.104,1.823 1.979,2.292 0.875,0.469 10 false from POWER Relay 0.125,0.083 3.25,0.323 3.125,0.24 12 false for LHD:

E376610E14
1.031,0.625 1.344,0.823 0.313,0.198 10 false H2 1.031,0.771 2.948,1.219 1.917,0.448 10 false Front Power Window Regulator Motor Assembly LH 3.208,0.531 3.521,0.729 0.313,0.198 10 false 2 3.208,1.125 3.521,1.323 0.313,0.198 10 false 1 5.146,3.927 6.719,4.469 1.573,0.542 10 false Power Window Regulator Switch Assembly LH 5.146,3.771 5.656,4 0.51,0.229 10 false H10 0.427,3.823 0.938,4.052 0.51,0.229 10 false G5 0.427,3.979 1.99,4.531 1.563,0.552 10 false Power Window Regulator Master Switch Assembly 1.667,2.917 2.177,3.146 0.51,0.229 10 false U 1.667,3.385 2.177,3.615 0.51,0.229 10 false D 1.833,2.813 2.115,3.021 0.281,0.208 10 false 10 1.833,3.292 2.115,3.5 0.281,0.208 10 false 18 5.219,0.375 5.729,0.604 0.51,0.229 10 false U 5.219,1.271 5.729,1.5 0.51,0.229 10 false D 5.219,1.823 5.729,2.052 0.51,0.229 10 false B 5.219,2.896 5.729,3.125 0.51,0.229 10 false SU 5.219,3.365 5.729,3.594 0.51,0.229 10 false SD 5.031,0.302 5.542,0.531 0.51,0.229 10 false 7 5.042,1.188 5.552,1.417 0.51,0.229 10 false 1 5.031,1.75 5.344,1.948 0.313,0.198 10 false 2 5.021,2.833 5.333,3.031 0.313,0.198 10 false 3 5.031,3.302 5.344,3.5 0.313,0.198 10 false 4 2.698,1.979 3.333,2.24 0.635,0.26 10 false POWER 1.104,1.823 1.979,2.292 0.875,0.469 10 false from POWER Relay 0.125,0.083 3.25,0.323 3.125,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH
a.

for LHD

i.

Remove the power window regulator switch assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL


ii.

Inspect the power window regulator switch assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL



b.

for RHD

i.

Remove the power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL


ii.

Inspect the power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH

2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH
a.

for LHD

i.

Remove the front power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


ii.

Inspect the front power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>INSPECTION



b.

for RHD

i.

Remove the front power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


ii.

Inspect the front power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>INSPECTION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH - POWER RELAY)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH - POWER RELAY)
a.

for LHD

i.
E367690C06
0.604,1.021 1,1.25 0.396,0.229 1.708,0.854 2.385,0.448 true 2.469,0.354 2.625,0.552 0.156,0.198 10 false B 0.677,1.052 1.021,1.229 0.344,0.177 10 false G10 0.375,0.385 0.583,0.583 0.208,0.198 10 false *a
*a Front view of wire harness connector
(to Power Window Regulator Switch Assembly RH)


Disconnect the power window regulator switch assembly RH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G10-2 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




b.

for RHD

i.
E367690C07
0.604,1.021 1,1.25 0.396,0.229 1.708,0.854 2.385,0.448 true 2.469,0.354 2.625,0.552 0.156,0.198 10 false B 0.688,1.052 1.01,1.344 0.323,0.292 10 false H10 0.375,0.385 0.583,0.583 0.208,0.198 10 false *a
*a Front view of wire harness connector
(to Power Window Regulator Switch Assembly LH)


Disconnect the power window regulator switch assembly LH connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H10-2 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH)
a.

for LHD

i.

Disconnect the G10 power window regulator switch assembly RH connector.


ii.

Disconnect the G9 front power window regulator motor assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-1 (D) - G9-1 Always Below 1 Ω
G10-7 (U) - G9-2 Always Below 1 Ω
G10-1 (D) or G9-1 - Body ground Always 10 kΩ or higher
G10-7 (U) or G9-2 - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the H10 power window regulator switch assembly LH connector.


ii.

Disconnect the H2 front power window regulator motor assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H10-1 (D) - H2-1 Always Below 1 Ω
H10-7 (U) - H2-2 Always Below 1 Ω
H10-1 (D) or H2-1 - Body ground Always 10 kΩ or higher
H10-7 (U) or H2-2 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY LH OR RH)
a.

for LHD

i.

Disconnect the H8 power window regulator master switch assembly connector.


ii.

Disconnect the G10 power window regulator switch assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-10 (U) - G10-3 (SU) Always Below 1 Ω
H8-18 (D) - G10-4 (SD) Always Below 1 Ω
H8-10 (U) or G10-3 (SU) - Body ground Always 10 kΩ or higher
H8-18 (D) or G10-4 (SD) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the G5 power window regulator master switch assembly connector.


ii.

Disconnect the H10 power window regulator switch assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-10 (U) - H10-3 (SU) Always Below 1 Ω
G5-18 (D) - H10-4 (SD) Always Below 1 Ω
G5-10 (U) or H10-3 (SU) -Body ground Always 10 kΩ or higher
G5-18 (D) or H10-4 (SD) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR