Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E254195E50
0.552,1.521 2.417,2.073 1.865,0.552 10 false from IG2 Relay*1 or Ignition or Starter Switch Assembly*2 1.615,0.708 2.521,0.979 0.906,0.271 10 false from Battery 3.969,1.698 4.583,2 0.615,0.302 10 false METER 3.896,0.875 4.906,1.177 1.01,0.302 10 false SECURITY 5.323,1.427 5.656,1.615 0.333,0.188 10 false 2 5.333,0.594 5.677,0.802 0.344,0.208 10 false 1 5.26,2.219 5.583,2.417 0.323,0.198 10 false 21 5.521,1.531 5.844,1.719 0.323,0.188 10 false IG+ 5.51,0.719 5.74,0.896 0.229,0.177 10 false B 5.521,2.313 5.854,2.51 0.333,0.198 10 false EP 4.958,2.854 5.594,3.104 0.635,0.25 10 false F38 4.958,3.01 6.917,3.292 1.958,0.281 10 false Combination Meter Assembly 0.146,2.979 2.521,3.271 2.375,0.292 10 false *1: w/ Smart Entry and Start System 0.146,3.271 2.521,3.563 2.375,0.292 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY CIRCUIT)
a.
E219772C29
1.427,0.125 1.917,0.417 0.49,0.292 0.563,0.5 0.615,0.958 true 0.479,1.24 0.365,1.635 true 0.281,0.594 0.469,0.969 true 1.563,0.188 1.896,0.427 0.333,0.24 10 false F38 0.167,0.438 0.396,0.688 0.229,0.25 10 false B 0.458,0.313 0.781,0.552 0.323,0.24 10 false IG+ 0.094,0.094 0.354,0.354 0.26,0.26 10 false *a 0.25,1.656 0.573,1.896 0.323,0.24 10 false EP
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-21 (EP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-2 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
F38-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR