Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM using the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E255800E28
4.74,2.563 6.958,2.813 2.219,0.25 10 false Combination Meter Assembly 1.771,2.573 3.01,2.958 1.24,0.385 10 false ECM 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 -
Body Electrical > Combination Meter > Active Test
Tester Display
TachoMeter Operation
50004 122 2
OK:

Tachometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE RPM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (ENGINE RPM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Rpm Engine speed Min.: 0 rpm
Max.: 12750 rpm
·

550 to 650 rpm (Idling (for 1NR-FE with Manual transaxle))

·

550 to 650 rpm (Idling (for 2NR-FE with Manual transaxle))

·

600 to 700 rpm (Idling (for 1NR-FE for CVT))

·

680 to 780 rpm (Idling (for 2NR-FE for CVT))


-
Body Electrical > Combination Meter > Data List
Tester Display
Engine Rpm
50003 122 9
OK:

Engine speed displayed on the GTS is almost the same as the tachometer indication.


HINT:
·

When the Data List values and tachometer values match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values and tachometer values do not match, an internal malfunction of the combination meter assembly is suspected.




Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FOR DTC

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 1NR-FE) B
SFI system DTCs are output. (for 2NR-FE) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C